Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Ping to one side only

Hi,I have a serious issue.. from my head office I can ping all the branches devices.. But from branches I cannot ping to any of the head of devices..What can be the issue? Please help me.

lzakariya by • Level 1
  • 1180 Views
  • 1 replies
  • 0 Helpful votes

Cisco C819G-4G

Hello everybody,I recently bought a Cisco C819G-4G, does anyone setup the 4G on this router? I've two different SIM card inside, the ISP are Vodafone and TIM. I'm from Italy. Best regards.

Resolved! BGP using route-maps within network command

Hello,I am hoping to get some advice regarding BGP and route-map configuration that we have on our MPLS router.  This config was implemented before my arrival and it has me somewhat confused.  We are advertising many networks out of our main office, ...

Unable to upgrade rommon on 2801

Hello, I would like to upgrade rommon on my Cisco 2801 but this is what I get:Router#upgrade rom-monitor file flash:C2800NM_RM2.srec.124-13r.T11This command will result in a  'power-on reset' of the router! Continue? [yes/no]: yesROMMON image upgrade...

Need help with Routing

Hello,We are setting up DID SIP Trunk on the PBX server. In this regard we purchased a Cisco Router 880 series and direct line from ISP connected to there MPLS network.Currently the PBX server is connected to our internal network and it is under vlan...

Resolved! PBR option

Helloneed some support on PBR0.0.0.0 route from the Backbone switch is forwarded to the firewall ; for a specific VC host on vlan89  we need to forward to a router vlan 88description Timeszip address 10.10.7.254 255.255.255.0vlan 89description VCip a...

Resolved! Problem With 2950 swith at startup

Hi ,I have a problem with Switch Catalyst 2950 T . At startup I see following error and SYST light blink green . I did the update IOS  but did not change .  Please help me to solve the problem.Thank you Done initializing flashfs.POST: System Board Te...

ASR 9k error

                   Hello, ASR 9k game this error can you one help what is this error?P/0/RSP0/CPU0:Jul 22 03:29:38.544 : pwr_mgmt[375]: %PLATFORM-PWR_MGMT-2-MODULE_FAILURE : Power-module 0/PM4/SP failure condition raised : Module fan failure observed...

Steev112 by • Level 1
  • 1779 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Nat address routing

I have a little difficulty with configuring nat pool routing.  I have 4 consective public address assigned to me.  I used two on each end of a site to site connection, both are routers.  There are two more public IP left to be used for nat pool.  In ...

Resolved! Upgrading IOS on a stack

So it looks fairly straightforward on upgrading the IOS on switches in a stack based on this:http://www.cisco.com/en/US/products/hw/switches/ps5023/products_configuration_example09186a00804799d7.shtml#cfbin1I am assuming that it is important to make ...

Convert a T1 connection to Ethernet?

I need to convert a T1 connection to Ethernet, and then plug the Ethernet into a vendor-configured SonicWall TZ205.  Seems like there should be a simple "media converter" type box that could do that for me, but I haven't found anything like that.I ha...

Tengig interface not showing

Hello,I am using a Cisco ME 3800 switch with 24 Gig and 2 Tengigabit interface. But after configuring the Tengig int with ip add and negotiation it is no know visible in the switch. Instead TenGig I am seeing two (Gi0/1 and G0/2). Not even showing th...

Load more