Activity in Technology and Support
Resolved! Cisco ISE TACACS+ to Fortigate Read/ Write and Read Only configuration
Hello,I am working on some Fortinet's and for anyone that has connected Fortinet's to Cisco ISE using tacacs+ I could really do with some help.TACACS+ > Active Directory > Separate Read Only group and Read/Write GroupArticle that I am using to config...
COMMAND TO FIND SERIAL NUMBER OF ROUTER/SWITCHES
ARE THERE ANY COMMANDS WHICH WILL GIVE THE CHASSIS SERIAL NUMBER AS OUTPUT, FOR ROUTERS? ALSO, IF ANYONE KNOWS A COMMAND FOR SWITCHES THAT WOULD BE HELPFUL.
Missing Visio Stencils for Cisco 8000
I recently downloaded the Cisco 8000 Visio Stencils.I noticed the equipment I was going to make a diagram of had missing MPAs and blanks.The following MPAs were missing.8K-MPA-18Z1DThe following MPA blanks were missing.8K-MPA-BLANK8608-MPA-BLANKI als...
Announcing Four New Cisco Secure Access Data Centers in the US
We are excited to announce that Secure Web Gateway (SWG) roaming traffic will soon be enabled for our newest data centers, located in: San Jose, CALos Angeles, CAMiami, FLReston, VA These sites are the first four data centers built on our Cisco Edge...
Announcement: GA Release of Enhancements for Resource Connectors
Resource Connectors in Docker Containers Support for Ubuntu 24.04 and RHEL 9 Feature Overview The Resource Connectors in Docker Containers support for Ubuntu 24.04 and Red Hat Enterprise Linux (RHEL) 9 is now Generally Available in Secure Access. Thi...
Dual-ISP Setup for Gaming Traffic Optimization
I am testing a dual-ISP setup at home to see how routing impacts online gaming performance. The goal is to:Use ISP1 for general traffic (browsing, downloads, streaming).Route gaming traffic (PUBG, Free Fire, COD Mobile, etc.) through ISP2 for lower l...
Resolved! Can't find software for my switch
Greetings! I have bought a used Cisco Catalyst 2960G 24Port TC-L, but I don't know if I can use the 2900 series main software. New to networking equipment as a whole. Just don't want to brick my switch I bought, I doubt I will, just wanna be 100% sur...
IBGP redistribution into OSFP on NXOS
Hi community,So i want to get some IBGP routes between two NXOS nodes, where one is running IGBP into the IGP (OSPF) onto the other node. This is to support a VM setup that the sever team claims has to come up on BGP and then be converted to our stan...
Unity Call Flow to CUCM with Transfer to Alternate Contact Number
I inherited a 2-node Unity Connection cluster and a 2-node CUCM cluster which have the SCCP connections between them. I'm trying to understand how the Unity servers determine how to pass Transfer to Alternate Contact Number calls to the CUCM cluster...
cisco sx20 downgrade to tc6
Hi,We must downgrade sx20 from tc7 to tc6, but not have .pkg file of tc6.and not exist in cisco site.please help to find tc6 for sx20.regards,
CSPC 2.11.0.5 GUI Events Not Logging to Splunk
We have configured our rsyslog.conf file to forward logs to a splunk forwarder, it's working to some degree; unfortunately, there are no GUI user account evnts showing in the logs. While researching this condition I find there is several possibiliti...
Host Name Unresolved 2.5.2.7 Packet Tracer
Hello, such a question for you: I am doing the work 2.5.2.7 Packet Tracer, according to the task, you need to follow the link http://www.cisco.corp to download files, but it says to me that Host Name Unresolved, no matter how I try to do it , still d...
Route leaks between VRFs
PE1 has two vrfs configured CE1A and CE2A.Both CE1A (155.1.111.11/24) and CE2A (155.1.112.12/24) are advertising their loopback addresses.I am trying to leak the loopback of CE2A (150.1.112.12/32) into CE1A without using the import route-target.I h...
9800 per slot RF Profile
I would like the ability to assign an RF Profile on a per-slot basis within the RF Tag. Am I being thick and missing the feature? For example: 5ghz Slot 1 assigned an RF Profile with 9 channel DCA plan (no UNII-2) and 5ghz Slot 2 assigned an RF Pr...
Trying to register new 9176 AP to Cat9800
Hi All-This is my first attempt to register / configure my new CW9176I AP to a Cat9800-CL controller. I have plenty of 9164s registered, but don't quite understand the 9176 boot sequence. It boots up, and get power:c3850-1u#show power inline gi1/0/...
| User | Helpful Count |
|---|---|
| 191 | |
| 127 | |
| 94 | |
| 91 | |
| 78 |
