Activity in Technology and Support
Looking for Linksys NMH405 Setup software
Hi,Is there anyone here who has the installation CD with the Setup Wizard for the NMH405 mediahub?I lost the CD and can't find the software anywhere. Would be great if you can share (the iso file for example)Thanks, Bastienne
Promiscuous mode error on FTDv 7.6.2
I upgraded my FTDv to version 7.6.2 and when i try deploying policy, it failed with this error: error : ERROR: cannot set np to promiscuous mode.ERROR: Failed to initialize interface, Add interface Failed. Has anyone seen this and any workaround?Tha...
Network Design: New Collab Lab + Home Cloud/ Wifi
I'm considering a design change where I consolidate two WAN circuits behind shared edge hardware in order to better leverage some existing hardware. The environments are currently structured as:- 2 ISPs- 2 firewalls- 1 Layer-3 Switch- 3 access Switch...
NAT DIA Tracker on IPv6 Interfaces
Hello, does it make any sense to setup "tracker-type ipv6-interface" which track via HTTP probes ? endpoint-tracker dns_t1 tracker-type ipv6-interface endpoint-dns-name cisco.com I tried several configuration but the probe still fails since mo...
Resolved! AIR-LAP1262N-A-K9
Hello there. I have this access point AIR-LAP1262N-A-K9, and it is autonomous and i want to convert in lightweight but i can not find the ios. Please how can i download anywhere ?
any suggestion ?
how do you retain the things you have learned so far . I learn for ccna ,and actually when i pass over a topic and go to another , i feel confused about the previous ones and i forget them .Some say that we should lab things to make them stick , and ...
Install of Cisco N540X-16Z4G8Q2C-D
Guys, I’m desperate here. I picked up this unit from eBay for my home lab, but it’s locked with a username and password. If anyone has the latest software or a USB boot image they could share, I’d be super grateful
IBNS 2.0 with ISE for dot1x
Hi all Hope someone can answer the below for me. Is a policy-map mandatory for dot1x to work when using IBNS 2.0 with ISE ? I have two ports on a switch configured for dot1x. Out of the two, one is configured without any policy map and the other h...
OSPF WildCard mask problem
hi every one...i am new in networking and i am bit confused in ospf wildcard mask..ospf configartion on routers are as follow:R2(config)#router os 3R2(config-router)#net 4.1.1.0 0.0.0.6 a 1% OSPF: Invalid address/mask combination (discontiguous mas...
dual isp failover on single asr1002hx router
hi,please tell me how i can configure dual isp failover on single asr1002hx router. I have 2 internet wires from 2 isp. I have /28 from ISP1 and /31 from ISP2. All servers behined my router is using IPs from /28. I want that if one of the ISP failes,...
Getting error on Catalyst 9000 Always-On Sandbox -20251231T08221062
i'm getting this error when try to launch Catalyst 9000 Always-On Sandbox -20251231T08221062@Torque was not able to complete launching your environment.For more details, contact your space admin
CUCM Cluster Migration Plan – Z-Maxs to X-Maxs
Dear Seniors,need advice on best practices for a CUCM cluster migration. Below are the details of the existing environment and the services that must continue after the migration.There are two companies:1st Company: Z-MaxsPurchased 10,000 DIDs from a...
Can you do Main and Extended from laptop on dual screen EQ room?
Hello, I have an request to use the USB-C at the table to do main and extended on the 2 displays connected to the EQ. This is as in using the room as presentation only, not in a call. Right now we are using the Atlona AT-OME-MS42 with great success ...
any suggestion ?
how do you retain the things you have learned so far . I learn for ccna ,and actually when i pass over a topic and go to another , i feel confused about the previous ones and i forget them .Some say that we should lab things to make them stick , and ...
Cisco Ise installation Stuck
I had 3615 k9 With updated firmware. I am attempting to fresh instal. 3.3 and 3.4 Trued both bootable usb method as well as kvm mapped dvd Its always stuck at random steps before ise installation Initially loading will start But after that Either it ...
| User | Helpful Count |
|---|---|
| 64 | |
| 57 | |
| 43 | |
| 35 | |
| 33 |
