Activity in Technology and Support
Routing in packet tracer
<p> </p><p>I am currently practicing the configuration of DHCP servers and routing in Cisco Packet Tracer in preparation for my exam.</p><p>My setup consists of two routers, each connected to two switches, with one DHCP server assigned for ever...
9300X-48HX IOS Downgrade
Hi,Two quick questions team.I have just taken delivery of 100 x Catalyst 9300-48HX devices all with cat9k_iosxe 17.12.04 installed.Company policy dictates that I must take them back to cat9k_iosxe 17.12.03 but I can see no differences between the rel...
How to show logs on a deny ACL ?
Hi AllIs it possible to show logs matching a deny ACL rule?When you add the log keyword to the ACL what exactly does this show you? just hits or will it show you a log of the actual source IP etc?If the above cannot be achieved, would you need to use...
ISE 3.3 patch 4 authorisation matching
Hi,Having some issues with ISE 3.3 patch 4 regarding MAB authorisation rules. We are using a third party product that ingests endpoints from ISE as well as from strategic span ports. By examining the traffic flows from the endpoint, it can then wri...
Certificate on wsa
Hi All, I have generated certificate from wsa appliance .pem format and same using on client machine under trusted root certificate. Can i use that certificate for https decryption or need to have CA signed or AD signed certificate. Pls note- User id...
ISE Profile for CW9176I AP
Hi,I can't see profile of new AP on ISE.Can anyone help me create or Import new Profile for AP CW9176I. We have ISE 3.1 for AP profiling. Thankyou in advance. Regards,Aamir Bhatti
CSPC - Connectivity service is not running
Dear,We have migrated our CSPC server from 2.10 to 2.11. ver. According to the Cisco guide, we followed the backup configuration process step by step, and all went well. After migration, we are not able to submit the collection job to Cisco. We are r...
Service sync on a brownfield network: it's a journey, not a destination.
Service sync on a brownfield network: it's a journey, not a destination. Nearly a decade ago, Crown Castle kicked off a network automation adventure with Cisco NSO. Today, that decision underpins the streamlined delivery of services on our nationwi...
Cisco CME SIP Trunk Call Fails with Cause Value 3 and SIP 404 – Help
I currently have an internal VLAN 1011, and all internal IP phones can communicate with each other without any issues. However, no matter what I try, I just can’t make outbound calls to external/public numbers, nor can I get the configuration to enab...
Resolved! UCCX15 Pre upgrade cop file
Good Day all,I am putting together a upgrade design for our phone system. Reaching 15 after years of upgrades on exiting hosts from 10.5 and likely before.I can see pre-upgrade checks cop files for CUCM IMP and Unity but cannot see one for 15, is the...
ERSPAN over Mgmt-vrf
I am attempting to create a ERSPAN session across two catalyst 9300 switch's management ports. I have been referencing the configuration guide for the catalyst 9300 (https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-...
Ospf on Subinterface not working
Hi, I'm trying to set up OSPF between 2 routers with subinterfaces. Unfortunately, OSPF doesn't come up with the subinterfaces. If I set up OSPF on the main interface, everything works fine. The connection is between different sites in the country. C...
MX85 Router
Not able to use internet, WAN port showing down on meraki portal. We have already done below stepsDisconnect CableReplace cableReboot the device
Resolved! APC UPS RADIUS AUTHENTICATION
I am running 2 PSNs in a PSN group behind F5 load balancer. I've configured RADIUS authentication for several other platforms without issue. When I'm attempting to configure RADIUS authentication for APC network management card 2, I never see the RAD...
Add Ip address on CUCM SAN certificate
HiI have CUCM 12.5 and my CAFor internal purpose, I need to add IP address as SAN on the certificat How can I do it ?
