Activity in Technology and Support
Cisco 2821 - Above memory requirements. What happens?
Hello.I currently just got a Cisco 2821 with CallManager(8.6) installed and IOS(15.1M) and ADVENTERPRISE installed. It has 512MB of DRAM and 256MB of Compact Flash memory. This device will solely be used for VoIP.I was wondering if it would be enough...
TLS not found
Hello,People can send me emails sometime and I can see that TLS 1.3 was in place, some time same sender is not able to send me email and get this bounce back alert"The following message to *@domain.com was undeliverable.The reason for the problem:5....
ISE VM in vCenter - not possible to terraform
Is it not possible to terraform a ISE VM appliance in vCenter?Sure, I can give the VM a name, and set resources like disk, cpu, mem, but other things like IP Address, admin passwords, enable API, set NTP servers etc doesn't seem to work.All examples ...
Resolved! Can I find my Cisco Contract number in my CSE or Webex account?
Stupid question, I know; But can I reference/confirm my Cisco Contract number in my CSE or Webex account?For support purposes, this would be much easier than having it external to the software. (And is done in many other software service products, o...
Upcoming changes to status.umbrella.com
We are excited to announce the latest update to the Cisco Umbrella Status Portal. This update enhances the portal's layout to prioritize customer-requested information. Additionally, it introduces the capability for customers to subscribe to service...
Decom CUACA Recommendations
We have CUCM 12.5 SR7 and Cisco Attendant Console Advanced version 12.0.5As we have now moved on to a new console solution (keeping the rest of the CUCM stack), I am looking for guides / recommendations / best practices to decommissioning the CUACA s...
ISE - know how many devices are authenticating with dot1x or mab
Hello, We have an ISE v3.3, authenticating devices with dot1x and MAB. Is there a way on ISE to know the following?: - how many devices are authenticating in total ?- how many devices are authenticating with dot1x?- how many devices are authenticatin...
NSO and a10 compatibility
Hi,I have just started picking up on NSO and currently we are in process of importing devices to NSO. When i import a10 devices and try to validate simple cli configurations i see that it is actually over-writing and deleting other configs at that le...
Twice NAT over VPN Tunnel to Azure
Hello everyone,Have a potentially interesting issue. We have a datacenter stack that is connected to a Cisco firewall which has a VPN tunnel established to the Azure destination. Inside the Azure network we have our VMs in our resource group with an ...
Issues with ports on Stack Cisco C9300X
Hello everyone, I have an issue with my setup. I have two Cisco C9300X-48P switches running IOS version 17.12.9, configured in a stack. The problem is as follows:The switches are connected to servers via dual links (one from each switch), with LACP c...
MPLS - "when/how" does the router build the LFIB
Hello all,I'm trying to determine the exact order of operations a router takes when you run mpls ip on the router, specifically when/how the router builds the LFIB table.The first step I have is that the router takes all the routes in the RIB and ass...
ASR-920-4SZ | 10Gb Port Activation
Hello, We have couple of Cisco ASR-920-4SZ routers, which we are currently using to connect to the Internet. We are planning to upgrade the access speed to 5Gbps which will require us to use one of the 10G ports. We did purchase the appropriate lice...
Smart Storage Administrator Equivalent Software
I have a Cisco UCS C240-M5L and I would like to know if there is a software I can install so our RMM software can see all drives on the raid controllers to alert us for drive failures. On HP servers, I can do this if I install Smart Storage Administr...
sending message to alerts@ironport.com
Hi Dear Cisco SupportI see an alert " Warning: Failed to connect to remote host 208.90.58.122:25 sending message to alerts@ironport.com " in ESA log and i never configured ESA to send alerts out to this IP address witch is belong to the Cisco. Could ...
Anyway to do disk health check (SMART) on ACI switch nodes?
SoftwareBIOS: version 07.17kickstart: version 11.1(3f) [build 11.1(3f)]system: version 11.1(3f) [build 11.1(3f)]PE: version 1.1(3f)BIOS compile time: 09/10/2014kickstart image file is: /bootflash/aci-n9000-dk9.11.1.3f.binkickstart compile time: 09/21...
| User | Helpful Count |
|---|---|
| 96 | |
| 65 | |
| 55 | |
| 48 | |
| 47 |
