Activity in Technology and Support
vManage API endpoint to pull Site Name from Network Hierarchy
I'm trying to see if there is an API endpoint where I can pull the list of sites from the Network Hierarchy section and potentially the devices under each site. As an alternate method of the data I am trying to pull together, I'm also trying to see ...
FlexConnect user disconnected after the AP disjoined the WLC
Hello Expert , As per my understanding the FlexConnect with central auth and local switch , will keep the clients "thats already authenticated" connected , however i had the situation where already authenticated users were disconnected from AP when A...
CSCwm03493 - UCCX Support for MSSQL JDBC Driver
Hello all, we worked with Cisco to get this change request added which is marked as an enhancement request. In a nutshell it is to update the available drivers in UCCX for making Datasource Connections for integrations to use a native Microsoft Driv...
RSTP forward delay
Hello all,Can anyone explain why RSTP does not have forward delay timers, and what are the port transitioning states.
CP-7841 Enterprise to MPP Conversion Firmware
I am attempting to convert some Cisco CP-7841 phones from Enterprise to MPP Firmware. I purchased conversion license L-CP-E2M-78XX-CNV= and was able to input the MAC and download a zip file containing <MAC>.lic for conversion. I installed the MPP fir...
CBW150AX-B stuck on Green Blinking
I have 2 cisco CBW150ax-B access points, that are Stuck in blinking green, both were working part of a 7 group of all CBW150ax's with a CBS250 POE switch, I have done the factory reset on then both, but they just continue to blink Green, off then gr...
Resolved! Gre source interface question
I have router a with a gre tunnel (tunn 1)to router b. Gig 0/0/0 to Gig 0/0/0i need to make another tunnel from A to a third on router C. C is connected to B on gig 0/0/1. No routing protocols it’s a small network all static’s. What’s the best way to...
Tagged vs Untagged Frames
I am trying to get a better understanding of why something is working. SW1 is another vendors switch which connects there devices, SW2 is my switch which connects devices on my network. SW1 and SW2 are connected via a trunk link that allows VLAN 30...
Network Design Help Please with VRF
I am facing an issue with integrating a new customer, Customer B, into our network. They have developed a virtual system that uses the same IP addresses as another one of our customers, Customer A. Customer B mentioned that it would take a significan...
CIMC cisco ise new disk in Raid 10 - Unconfigured Good
Hi!We had a broken disk on our cisco ise server which is setup using Raid 10.Went out with a new disk same size and everything but different brand, Seage instead of Thosiba BUT everything else is indentical.The disk shows up fine in CIMC, but says Un...
WLC9800 APs unjoin
After i delete the APs that is unjoin in my controller, after a few seconds some APs show up again as same status unjoin and when i try to delete, it pop up again, if you have any suggestion how to solve this issue gladly appreciate it.
Resolved! How to install a godaddy .crt file on ASAv10
Hi All,I have .crt file from Godaddy that I need to install on my ASAv10 identity certificates. In ADSM the add button wants a pkcs12 format and Godaddy only provides .crt and pem files. I could really use some advice/guidance. Thanks all!Cisco Adap...
User and Machine Authentication
Hello Am having troubles getting my WIFI to work with machine authentication and user authentication i keept trying to reauthenticate every time im not really sure why it doing it at the machine authentication part, but it get that correct. this is w...
Resolved! Taildrop avoidance for critical traffic
Hello Experts , I have a critical application traffic which passing though my Cisco ISR 4321 and i noticed that some packets being dropped as Taildrop , Please find below output from packet-trace debug : sh platform packet-trace summary | i Gi0/0/...
Update FPR1010 to 7.4.2-172
Hello. I'm trying to update a firewall running FTD, managed via FDM, from version 7.0.1-84 to version 7.4.2-172. I uploaded "Cisco_FTD_SSP_FP1K_Upgrade-7.4.2-172.sh.REL.tar" on the System Upgrade section on the Updates page of FDM. When I click Up...
| User | Helpful Count |
|---|---|
| 85 | |
| 80 | |
| 65 | |
| 64 | |
| 61 |
