Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Hi Guyz, May b awiered Question but this is my users requirement I have CCM 8.5 and Cisco 7942 IP Phones,I have users who want to do Internal Call Conference up to 6-7 users at a time and call outside users 2-3, Cisco 7942 only ...
HiI have read the upgrade guide for cucm 9 and i get confused could you pls verify the below?1) i have to install the cop file for refresh upgrade2) in this guide is say that we have to install fisrt the license for 9 and then to perform the upgrade ...
We are upgrading CUCM 6.x to CUCM 8.x As a result we would be using attendant console 8.x operator instead of the present Attendant console operator 6.x(which comes with CUCM 6.x)With CUCM6.x, we had a DDI of 3555 which ws translated to 1100 as...
Hello AllI am trying to get into the Cisco Survivable Remote Site Voicemail - Administration website and i can not remember the credentialsI signed into the cueand typed the followingweb admin cme hostname x.x.x.x username admin ...
Cisco Unity Express - Serviceengine Boot Loader>I am in process of installing and configuring Cisco Unity Express. I configured required IP and default Gateway for ISM 0/0 Interface. Now when I do service-module ism 0/0 session command it give me ser...
Hello folks,The management wants me to make a list of new CUCM to order.I really don't understand how to do it. I've found that there is workplace license and ESW. But I don't understand it.We have CallManager 4.3 that needs to be upgraded to CUCM 8....
Hi Experts,Greeting for the day!!I am facing issue in visual voicemail.Pre-request: Subscribe visual voicemail service in the phone.Step to reproduce: •1. Press the message button in phone•2. Phone show two option voicemail and visual voi...
Last Thursday morning I set up a WebEx conference call off of my calendar. The invite sent to everyone but it disappeared off of my calendar and when that occured, the invitees could not call into the conference line. Then on Friday I set up a meeti...
Hi,I have one c210 M2,which have 16 1 TB hdd,i want to install esxi 5.0 on this server.i want to configure raid 0 or 1 for 2hdd for esxi,and raid5 for vms datstore,but when i go to raid ocnfiguration wizard there is no option for raid 0,1,5,there is ...
Dear Support ,Previoulsy We are running Cisco voice Mail system , later we upgrade to cisco Unified Messaging System i.e cisco Unity 7.0 .most of the user extension are configure from Callmanager 7.0 as "Forward No Answer Internal" to voice mail s...
Cisco Unity Connection(UCxn) is now supported to run as a virtual machine on the UCS E blades. The support is limited to 100 voicemail only users with 8 voice ports. The requirements and support are documented here - http://docwiki.cisco.com/wiki/Cis...
I have been trying to get the MWI stutter tone working on my system. Voicemail is working but when you pick up the handest you do not get the stutter tone to indicate there is a new message. I have attached my unity conf and router conf. clock timezo...
Hi all.I want to block all national/mobile calls from my phone (i.e either from my deskphone or my DN) and only allowed after entering any sort of PIN or password. I am using CUCM 8. I want only my phone (or DN) to be affected, this policy shall not ...
Hello Guys,We setup the Message Archiver on a RHEL platform. Couldnt do it on Windows postgres. It is working fine. But how do i retrieve chats now ? I searched and there were no support documents for this. PDI didnt help much as well.. ThanksVaradar...
hi! How do i redirect incoming call to another line group if the call is busy or no one pickup after sometimes in CUE7 (auto attendant)Basically i want the incoming call that has been redirected to IT Dept's line group using the autoattendant, to be ...
