I need to change the IP address of my UCS 200 and for sme reason it will not work th e address is X.17.1.162 if I chnage to x.16.1.162 it fails if I change to x.17.1.242 it is okay.. So it looks like if I chnage the subnet it will not work..Any ...
I need to change the IP address of my UCS 200 and for sme reason it will not work th e address is X.17.1.162 if I chnage to x.16.1.162 it fails if I change to x.17.1.242 it is okay.. So it looks like if I chnage the subnet it will not work..Any ...
So we were "gifted" a UCS C250 M2 server. Very nice of our Cisco Rep, who has been very good to us.The server just got RMA'd due to a motherboard issue diagnosed by a remote TAC engineer.How often does this happen?During our TAC case, the first engi...
If I wanted to shuffle some blades around from Chassis to Chassis in the same domain, but leave the server in-tact IE don't reprovision, format drives, etc.. simply a shutdown/move/power-up scenario. I've though through a few scenarios but I'm not su...
Hello all & greetings. Is it correct that if I have a fully configured N7K / N5K without the FCoE and NPV features enabled and subsequently ENABLE both these 2 feaatures, I will lose all configurations? Is that NX-OS version dependent? Any work aroun...
When looking at the different options for downloading ESXi, I see Dell, HP, etc. Is there a version that we should use for UCS? Thinking we are going to start with 4.1. Thanks!Craig
Guys,I have an issue with the Nexus 1000v, basically the trunk ports on the ESXi hosts stop inheriting from the main DATA-UP link port profile, which means that not all VLANS get presented down that given trunk port, its like it gets completey out of...
Hi all,I was wondering if anyone has had problems connecting to a ESXi 4.1 or 4.1 U1 installed on B200, B230, B250 or B440 blades. My UCS is currently running 1.4.3(q). At this point, we can ping the Host just fine and the host can ping out just fi...
I have service profiles and blades running off of that service profile. Each blade has two vNIC's and I need to add two more vNIC's to them. I want to add the additional vNIC's to templates and let the service profiles get "updated" with the new vNIC...
Do Appliance Ports Require End Host Mode?We are running switch mode, and wondering if I have to change to End Host Mode for Appliance Ports?Thanks!Craig
Hi,we have some UCS-B and some leds of their PSU's are blinking and the status is N/A. Status detailed can be seen in the screenshot: The strange thing is this state doesn't generate any fault.Does anyone know if PSU's are really working bad or is on...
Hi everybody:I'm looking for a tech paper that state the relationship between the PSU and Blades in a 5108 chassisI want to resolve design questions like:How many PSU I need if I have only 3 half size blades and I want redundancy N+1?Or how many PSU ...
Hi there:I'm lostI know when you have for example two uplink ports that belong at the same vlan, and two or more vNICs asociated at this vlans, pinning happen dinamicallyI know how configure a VLAN and assign it to an vNIC But I can't found how to as...
Hi folks,Kind of seeing something that is really strange. I have built out a service profile and bound my vNICs to vNics template. On vNic template, I only have a single VLAN assign to it and the service profile has the same vlan. I also have mul...
Hi all,I am trying to setup a raid configuration on my c210 M2,i am not using the onboard raid controllerd because i am using SAS Drive's.In my c210 there is a Mezzanine card, the labal say's: S98 SAS: 000 298D51The manufactur is ARM made in korea.No...
I am pretty sure the answer is no, but is there a way to expand the MAC-Address Pools or any of the pools through the UCS MGR ?If not why is that not an option ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-06-2025 10:22 AM | ||
01-31-2025 04:20 AM | ||
01-30-2025 02:32 AM | ||
01-29-2025 09:54 AM | ||
01-23-2025 11:09 AM |