Hi allI have a IMC supervisor installation running 2.2.0.6It has lost eth0, which is the appliance primary interfacewhen i try to configure eth0 the message is "Device eth0 does not seem to be present, delaying initialization"Could look like this sce...
Forum Posts
Hellowe have an UCS Chassis with 8 Blades two of them running Xenservers providing VPS services using Cloud Citrix, Recently was asked me to add more blades with Xen Servers too with similar setting to the existing setup but for new and different env...
Both of my fabric interconnects are complaining about too little disk space. But I'm not sure where to go to see what junk I can delete from there. In UCS Manager there's no place in FI to show the contents of bootflash. I went to the CLI and tried c...
Resolved! how to verify ucs uptime?
Hi All, I observed UCS alert on my monitoring tool. Service : System Uptime State : OK Hostgroup: Switch Time: Tue Apr 15 19:10:16 UTC 2014 Additional Info: OK: UPTIME=34 minutes, 11.37 But when I logged in and verified the system uptime, it was up f...
Hey all Currently our UCS has connected 2 old cisco 9148 switches, vsan 10 and 11. We plan to add a new set of new 9148S MDS on new port-channels on the FIs with the same vsans. These MDS will not be connected between them in anyway (ISL). Will the F...
Hello All, I am a newbie to Cisoc UCS E-Series Server ( with ISR 4331 ). I was configuring the CIMC IP. Below is the config I did for CIMC Access using the E-Series Server's Internal NIC GE1 and routers UCSE 1/0/1 Interface. Physicaly Conne...
Hi All,I have been using Python sdk of UCS, ucsmsdk for managing fi operations.But i could not find the appropriate one for the 'show flogi database' output.Looked at all mometa classes. But could not find it. Please let me know if the same is availa...
Resolved! Cisco UCS5108 2208XP I/O Module Manage?
Hi I bought used Cisco 5108 Blade System with 2 x UCS 2208XP I/O modules. This module has an HDMI port instead of a serial connection. When I researched this module, I read articles as an expansion slot. Can I manage this system without fabric interc...
Hi All,I have been using Python sdk of UCS, ucsmsdk for managing fi operations.But i could not find the appropriate one for the 'show mac address-table' output which is shown below.fi-B(nx-os)# show mac address-tableVLAN MAC Address Type age Secure N...
Very long story short, need to upgrade VM Tools from 10.x to 11.x on 100s of auto deploy 6.5 U2 ESXi hosts (UCS Blades). The customer is NOT in a position to upgrade to 6.7 with the latest 11.x tools already embedded. I am trying to create one of the...
Hello!I have a Cisco C240 M3 server with 24 2,5" HDD slots. When I try to add more than 12 disks some of the disks are not detected and show the yellow warning light.Does anyone know how to resolve the issue?
DETAILSDisk - SAS 7.2k 1TBVMware ESXi v5I was following the configuration guide http://www.cisco.com/en/US/docs/unified_computing/ucs/c/sw/os/vmware/install/VMWARE-esxi-install.html to install VMware ESXi v.5 on a Cisco UCS M2 LFF which has a disk - ...
Hello Everyone, I was hoping someone within this forum could assist in a problem I'm having at a client site. So we have two UCS C200 M2 blades that we are unable to access CIMC from. When I try to reach the IP the browser just sits there, but the IP...
I've been trying without success to get IPMI working on B200-M3 blade servers. I created an InBand management IP address on the CIMC, by creating an IP Pool and associating it with the appropriate VLAN in a VLAN Group, then using that in the InBand P...
Hi!I'm having an error while validating the UCS environment in the HyperFlex Installer.The error is:Reason: 'FabricSubGroup' object has no attribute 'oper_state'The only probable cause that I can think of is the fact that the uplink from the FI to th...
Recognize Your Peers
.jpg "VIP Mentor"){kind=icon}
