Wireless

Hi! I am new to wireless things and maybey someone can help me with my problem. I have two 1130AG Accesspoints. I have set up one with WPA-PSK and that one works just fine after some configuration. However I have now purchased another one to be able ...

Hi,I have a wireless link from an elementary school to me. The link consists of my Cisco BR500E V8.80 (340) as the root bridge. The school site has 2 buildings with Cisco 340 and 2 buildings with Cisco 350 bridges. I have WEP enabled. The links have ...

HiI need to know what cisco device(s) currently support 54Mgb with distance coverage of 15km?. I would apritiate it if you could also tell me what antena series (if requered) is also needed.Thanks

HiWe're using AP1200's with PEAP-GTC and a Radius server running ACS v3.1 with a RSA Ace Securid server for authentication. The problem that we have is that the passcode failures aren't passed back to the wireless client for the Dell TrueMobile 1450 ...

Hi there.I have an installation which consists in a Cisco Access Point 1100 and a freeradius server connected to a LDAP server.I want to setup several VLANs and assing them to the users depending on what group they belong to. All the freeradius and L...

Our current method of configuring switches is via a TFTP server. In DHCP we give the MAC of the switch a Manual DHCP IP, this causes the switch to pull its name as its initial boot name. When the switch boots it looks for its name-confg. This piece...

We are looking at using SSG/SESM to deploy WLAN Hotspot networks to our clients. I would like to ask the following from anyone interested in a reply:1.) How difficult is it to deploy - what is the typical time spent (I know that's open ended based o...

Just attempted to upgrade a 1100 from 123-4 to 123-7. Boot fails (three green solid LEDs for 1-2 mins and then a red status. Unit reboots, over and over). Tried to load it via TFTP with the same result. Reverted back to 123-4 and all is well.Anyon...

I know this has been kicked around on this forum before, but I am trying to look deeper into the issue with the 2200B/G card.I work as a wireless consultant for a company which performs many wireless installations, both Aironet and Airespace in Hospi...

I was reading this Cisco Q&A doc (http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item0900aecd801764fa.shtml) that contained the following question and answer:Q. Can I use PEAP with LDAP or Novell NDS databases?A. Yes. PEAP provi...

Does anyone have any information/documents on how to get EAP-GTC authentication against a Novell eDirectory database? The ACS docs do not mention that LDAP is required to get this working, just the Novell Client, but several posts here state that a ...

HI, I am using Aironet 1200 AP, ACS 3.3 with 802.1x authentication, when I am enabling win XP utility insted of Cisco ACU it's wait for certificate credentials. I installed CA authority in windows 2000 server. But i am unable to accessing wireless ne...

Can the WLSM module function using the WDS Service only? Without L3 Roaming enabled?If I configure the WLSM for IP connectivity and WDS functions only, will it work? I'll be wanting to configure it for layer 3 roaming later, but not yet.thanks,Paul

hello,i browse http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.htmlmy question:1. can we use: AIR-CAB150ULL-R - 150 ft. ULTRA LOW LOSS CABLE ASSEMBLY W/RP-TNC CONNECTORS2. AIR-ANT1728 - 2.4 GHz, 5.2 dBi Ceiling Omni Ant...

I am using a 3005 and Aironet 1200. When I use these 2 together I am not able to login to my novell server, I am not able to ping the server either. If use one or the other of these technologies alone I have no problems but when I use them together...