Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
How to find BSSID of AP's WLANs directly connected to C3850 I know for Cisco wireless controllers, the below command shows the list of BSSIDs for that AP,show ap wlan [802.11a/802.11b/802.11-abgn] <Cisco AP> Can someone help me with command to list t...
Hi, we have one main wireless controller 55xx and one mobility anchor controller 55xx for some WLANs (SSIDs). Now we need to upgrade the main wireless controller OS to support the latest catalyst 9K access points, but anchor WLC os is still 8.5.x, do...
This is why the "new" roaming tab on the client view is so good.See how my notebook roamed from an AP with -43 dBm of signal strength to an AP much further away with a signal strength of -67 dBm (a number closer to zero is better)?This is a 100% clie...
I have a quandary. I have 6 MS access points we just setup. 5 of the 6 work just fine. One allows us to connect but it continually says no access. We are not doing PEAP/EAP or any radius configurations. We have pushed a profile via intune to have the...
I’ve got a challenging environment that I’m looking to improve Wifi coverage and capacity in. It’s a parking garage for city transit buses. The building is somewhere in the neighborhood of 240 feet across and around 600 feet long, but the flat roof i...
Hello, I am moving all my on prem servers remotely. I have created a new NPS installation on a new server. I then exported the NPS configuration I had on-prem and imported it to the new server. It starts up fine and I can see all my access points und...
hi, can anyone please help advise what vlan will the client be put when the client connect to an SSID "test" and AP is in flexconnected mode. The ssid "test" is not in vlan mapping table of flexconnect, it is centrally switched. Thanks in advance. o...
We have these Cisco access points. When the firmware was an older version, I configured the 2.4GHz and 5GHz bands both in one SSID through the GUI. Now that I have updated the firmware to a new version, I want to configure the 2.4GHz and 5GHz bands b...
Hi ,MR30.5 went from beta to stable release candidate. The changelog were changed.Old : Wireless firmware versions MR 30.5 changelogIMPORTANT NOTEWhile Meraki APs have traditionally relied on UDP port 7351 for cloud communication, and TCP ports 80 an...
Morning We have 2 Cisco 5508 WLCs, we have around 50 1142N APs across the campus, all of which use DHCP and PoE without any issues. The WLCs are configured as DHCP relay agents which works perfectly well for both the APs and Clients. We had a need ...
Hi. I have borrowed an AIR-AP1840I-E-K9 access point to perform some tests on radio signals so I'm not that familiar with the configuration of this access point. It used to work fine and the DHCP would assign an IP address to my PC as it should, but ...
Hi there; I have a cisco AP called "AIR-CAP2702E-E-K9" and I want to convert it from Lightweight to Autonomous. I read many post but I failed to do so. The problem I am experiencing is that no interface is shown in PuTTY so that I can do the configur...
I just put together a network with MS225 switches, to a MS425 core stack. I'm deploying MR57 APs and seeing a number of good APs in the Topology, but also a number of blue diamondsThe diamonds, when hovered over, show they are actually repeats of the...
Hello community. I need to set up an SSID with integration to Azure AD. Does anyone know if this configuration is possible?Thanks,Jackson D.
Dears, I need urgent support, I spent like 12 hours troubleshooting a wireless issue on my Cisco WLC 9800 for .1x authentication that was working & suddenly stopped. The software code is 17.9.4a & 17.12.1 Here’s the logs on the WLC: Feb 4 16:16:34....
