Cuando se me vence la licencia DNA, de igual forma se puede seguir configurando un AP C9115AXI-EWC-A?
Forum Posts
Resolved! 9115AXI does not join to EWC
Hello, I have a setup that consists of 4 9105AXI aps and one 9115AXI ap. I have upgraded all APs to version 17.6.4, and was able to join all 9105 APs to the EWC on the 9115, except for the 9115 itself, that did not show between the APs. any idea? Thx
Resolved! AP 2702
Hi,I got an AP 2702 with the Giga 1 interface up but protocol down.I tried shut and no shut, and got the same.Here is the show interface command:GigabitEthernet1 is up, line protocol is down Hardware is PowerPC Ethernet, address is e865.49d2.c89d (bi...
Hello, I have a question about updating the IOS of the WLC 2504 and backing up the license files in advance and then importing them again after the backup to a higher IOS version has worked. I hope someone can help me there. Oh yes, I am a nature Ger...
Clients are displayed as ipv6 ip.Clients are not receiving ipv4. I checked the config as below. - Checked Controller → Interface → VLAN- Checked WLAN interface mapping- Checked WLAN DHCP override- After deleting the Client wireless profile, checked t...
Hi,We are using cisco WLC 5520 for our wifi connectivity with HA configured. Since last few days i am observing a strange behaviour from my standby controller which i had never observed earlier. Controller is rebooting after the below activities:1. ...
What is the recommended height to mount the Access Point C9120AXI-S to mount above the ceiling, below are the clean room areas?
Hello, As mentioned in the Title. I've created a template on cisco prime to be deployed on 9800 WLC's. However when I'm at the template, and click deploy no devices show up even though I'm able to see the device in Network Devices.Anyone experienced...
Hi all...Checking configuration of the Vlans... just seeing that:we have 4 Vlansfrom router to switch- VLAN 1(default), ID: 1- VLAN 100, ID 2- VLAN 110, ID 3- VLAN 130, ID 4and on the WLC there are 3 WLAN configured:- WLAN 100, ID 1- WLAN 110, ID 2- ...
9800 WLC 17.3.3 + C9120AXI APsset guest wifi L3 web authentication, consent, captive portalFor iPhone all good working, but for Android devices (mostly Android10+) can't pop-up captive portal.It occurs sometimes, for example: on Monday( 2 days off o...
Resolved! WLC 5508 Airos 8.2.170 AAA with ISE 3.0
Dear All,In a test environment, I'm setting up EAP-TLS client authentication and authorization using DACL.Authentication works. Although I haven't configured DTLS yet to secure the Radius protocol communication between the WLC and ISE. My first quest...
In order to provide hardware support, I have the necessity to register certain Flex Connect APs with two different Catalyst 9800 Wireless LAN Controllers (WLCs) running different software versions. To guarantee uninterrupted mobility across the APs m...
Hello,I am attempting to send a COA request with Request ID 44 by utilizing the Acct Session ID and Calling Station ID that were extracted from the Access Request Packet. I have sent this request over port 1700, which has already been enabled on the ...
Resolved! Merkai splash page with (PSK) question
Dear All, I have recently created an ssid "wifi-guest" with splash page (PSK), when i use my iphone to connect wifi-guest and credential popup in seperate page rather than inserting psk password in the splash landing page, is that normal ? Keith
I had about 120 APs go offline on the dashboard yesterday. They cover about 3 of my locations. They are still delivering connectivity but I can't see them to manage them from the dashboard. I also can't go out to the web address on my LAN to see them...
