Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
So I am relatively new to professional IT. I have been given control of a ton of things with the company I am with. One of those is our Wireless Network. We are not a huge company. About 200 in office workers total. We have 4 main buildings containin...
I have a used AP(Mr33).To configure I first reset the ap then I went to the Meraki dashboard with a new account. When I tried to add the AP as a new device. When I typed the serial number it said its already in use
Hi Experts, I'm getting multiple alerts from Prime regarding the issues in Access points. below is the log message.''Message: Access point 'XXXXXX' associated with controller 'XXXXX' draws low power from Ethernet. Failure reason: 'The AP draws 15.4 w...
Hi, 1) I'm convinced there is a bug in the 145 AC 10.4.1.0 GUI software regarding the native VLAN. I've tried changing the native VLAN in "Global AP configuration" and it always fails with an error along the lines of "Error in setting IP" or worse it...
The inbuilt WiFi has been getting flaky and now won't connect on my Panasonic cf52 win 7 laptop. Initially it would disconnect and the lights would be flashing and eventually reconnect. I have replaced the card a number of times and this time the car...
We have a dilemma. We have a site that has 34 1532E and I AP's that are NOT budgeted to be replaced this year. This year we are replacing the old 5508 WLC because vulnerability patches ended this year. We bought the 9800 controller replacements and s...
Dear All,Greetings,I am recently facing this problem my two 1852 APs are unable to join with controller. They were working fine for last six months but suddenly they are unable to join the controller. Below are given complete boot up process output...
My organization inherited a 9 slot 6500 chassis from another department. Included with this chassis was a WISM2, The 720 supervisory engine, and 48 port switch blades. We are currently using just those 3 blades to provide our organization with Wirele...
Resolved! Setting up a WISM2 to replace a WLC 4402
We are replacing a WLC 4402 with a WISM2 we inherited from another department. The WLC 4402 has three interfaces. AP-manager (APs), Guest, and a secure for interior share access. I was successful in setting up the new AP-manager on the WISM2 with it'...
How can I easily check/verify FIPS-2 compliance of each SID my WLC?Model: 2504VER: 8.5.151.0 Thanks-
hoping someone can point me to a resource... We have a Cisco c1111-4plteea with GPS enabled, but it is flooding the server with coordinates, reporting over 200 times per minute.. Is there a way to throttle or control how often the coordinates are se...
Hello, I have a problem about HWIC-3G-HSPA card.Line protocol is becoming always up/down and there is message on screen "Mailbox msg transmit failure".Is there any opinion about failure and how can I solve this issue? I am sharing soma screenshots f...
Resolved! Cisco 9800 Wireless Controller Licenses
Hi Teamwe are upgrading to cisco wireless controller as attach details of products & Boq,please clear me below things :1) C9800-80-K9 : controller required separate licenses or only access points need DNA-E Or DNE-A licenses ???2) controller C9800-80...
Hi,My 3602 running 15.3.3JF12i will only broadcast on 802.11N over 2.4G only. The config I have is: dot11 ssid LM0701band-selectauthentication openauthentication key-management wpa version 2guest-modewpa-psk ascii 7 xxx-snip-interface Dot11Radio0no ...
while i am in office, i have my IP phone connected with network. whereas now i am doing work from home but my IP phone not working even i am working my office server via VPN. at home i have good internet speed.
