Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi Team, I have configured TWO VLANS for LAN and WIFI... Wifi is configured and connected on ASA MaManagement port and wifi is working finewe are not able to access from Wifi vlan to lan VLAN Can any one help me to resolve the issue thankssuresh
Hello Meraki Community,I have been told that the Meraki Layer 7 Firewall solution available in Meraki MR AP dashboard is based on best effort, as it is not able to block certain traffics even if they have been defined within the Layer 7 firewall rule...
Hello, I have just setup a test vWLC in a lab and connected a AIR-CAP2702I-E-K, the controller can see the AP, I have configured a few SSIDs but I cannot see them being broadcasted?Any suggestions? Wireless
Hello together, i am currently struggling really hard to get a AP2802i to run as a Bridge / WGB Mode. I have the CAPWAP Version and the Bridge-mode should be available, but its NOT. When i try to change to mode from "local" to "bridge" i get this Mes...
Using a WLC 5508 and ACS for web authentication for users wireless users. The virtual IP 1.1.1.1 has been always set to take the users to the authentication page. All of a sudden it stopped and is now sending users to the page attached. Can someon...
Is it possible to provide locally switched guest wireless access in flexconnect mode with Web-Auth? All of the documentaion examples I can find show guest webauth with central switching. I want a remote office, connected via DMPVN, to provide guest w...
Cisco 5520 / 8.5.140Starting to roll out IPV6 testing on the WLC and I'm running in to trouble adding vlans with IPV6 interfaces to the controller.I've added 1 dynamic interface (vlan 120) with a ipv6 address / 64 / and the link-local address of a ro...
Exact behavior desired is Guest WLAN clients will see a webpage built-in to the controller that will warn them of our policy, but they will not have to enter a password--they will only need to click on an accept button. Is that doable on the 5508 run...
Hello, I'm wondering if when you set multiple mandatory data rates, example 3, that means a client MUST support these 3 data rates or it has to support one among the 3 mandatory data rates ? Example, most of our rf profiles 5Ghz Data Rates are config...
Just wondering if there is a workaround to supporting two factor authentication with the Client VPN. The url here says it doesn't without using a third party tool: https://documentation.meraki.com/zGeneral_Administration/Other_Topics/Two-Factor_Authe...
We are happy to announce the second refresh of 8.10MR1 Beta Program for PRODUCTION deployments. 8.10.109.48 is the second, qualified Beta Image and is fully BU supported. After previous 8.10 CCO, this program is focused on hardening the software qual...
I am trying to configure the internal AP to join a wireless controller. It is in CAPWAP mode but I keep getting the following log Jan 10 15:59:42 kernel: [*01/10/2020 15:59:42.2299] Waiting for preferred uplink IP configuration How is it supposed to ...
***Foreign & Anchor WLC 5800 ver: 8.2.166.0*** I have 4 WLCs. 2x WLC in HA as foreign controllers. 2x Anchors in DMZ. On the foreign and anchor WLCs, there are two guest SSIDs configured. Guest1 and Guest2. For each guest SSIDs in foreign, WLAN > M...
Greetings, We are happy to announce the first refresh of 8.8MR3 Beta Program for PRODUCTION deployments. 8.8.128.29 is the first, qualified Beta Image and is fully BU supported. After previous 8.8 CCO, this program is focused on hardening the softwar...
Hi, Ive got a number of 1117's with wifi to configure and id preferably not use the gui to do it. I need to tag vlan 10. I have been able to work out the config I need to apply to the controller for the most part apart from Vlan tagging. Any idea how...
