Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I am trying to deploy a Code Blue analog unit which has been programmed internally for RingDown dialing. I configured the ATA 190 with a DN in the normal CSS. When I connect an analog phone to the ATA I can dial internally and externally to/from our ...
Hello, I have an issue with CUCM 8.5. A user have 2 lines in their phone, is the same number but in different partitions (Line1_PT, Line2_PT). A secretary needs to monitor his line status, but when a call come in his Line1 extension the two BLF bu...
Hi, I can't find an up-to-date compatibility matrix for CUAC against CUCM to cover version 11. I need to verify what versions of CUCM v11 support CUAC advanced. Many thanks, John.
The message below appears in the Syslog Viewer section of the RTMT application. Why is this happening and what can be done to resolve it? : SELinux is preventing /sbin/ifconfig from search access on the directory /proc/sys/net/ash. For complete SELi...
Hi Guys, I am working a new build and restore of CUCM 9.1 and I noticed that some cop files were installed. Before I do the restore should I install these cop files? Will it fail if I perform the restore. I am thinking that it will fail. Just want t...
Hi Team, I am trying to figure out solution for following requirement. Call Hits Number > greeting is played twice and there are three options 1, 2 & 3 to choose from. It works fine upto this. Option 1- is for call Forwarding - Works Fine Option 2...
Hi - I have the above conference phone and would like to configure this. All of the documentation indicates i need to manage this unit via Cisco Communications Manager. I have a simple network setup.... Internet - Basic Modem - Basic Switch - Cisco ...
Hi, I'm running latest version of CUCM 11.5 (1) SU2 and I have noticed that TFTP service shuts itself down all the time. This is the only service that has problem and I can't find the reason. Please provide some guidance what needs to be checked and...
hi i use unified CM 8.6.2.23900-10 and trying to register 8841 but the CUCM does not have the phone type, recommendations or suggest device pack to install and how..thanks.
We are using SIP provider (203.52.0.167 in the diagram below, same as aces.com.au). I am having an issue when dialing for instance 0300003876 from 88855670. In diagram below 10.61.64.254 is the CUBE and 10.61.2.82 is CUCM. The problem with the call ...
Hello , I am trying to change the moh in the confernce now . I am not sure were is this option "MOH Source While Participant is Waiting" Anyone knows ?
Hi all, how to make translation profile for 1 calling number and 1 called number? or is it possible to make 2 pots dial-peers having 1 voice port? I want to try to make 1 pots dial-peer like .T and second as destination number pattern 2111 which m...
call manager version: 11.5.1.10000-6 ip phone model 7861 ,8845,8861 sip ip phone firmware version sip8845_65.11-5-1-18 sip88xx.11-5-1-18 sip78xx.11-5-1-18 I configured srst router and call manager srst click then ı choose in device pool srst mode ...
Hello, I need your help with the next issue. I bought a CISCO ATA 190 to replace an old CISCO ATA 186 that died some weeks ago. When i installed the new 190 i found that i can't change any settings from the web page and our infrastructure doesn't i...
Hi.. I have Cisco 2911 router with 4 E1s activated on it. And 1xPVDM3-16 & 1xPVDM3-128. Every alternative day, all the E1's start flapping. After a reload of router, the E1s become stable for few days and then again start to flap. IOS version : c2900...
