Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi everyone,We have a UC520 with a T1 connection and incoming DID calls. as long as a normal call handling everything works fine. I mean someone dials a DID from outside and an extension on the UC520 rings.now they decide to move to an Asterisk PBX, ...
Hi I have a CUCM 7.1(5) with a trunk sip to a third party Contact Center....All SCCP phone can call perfectly to the Contact Center and press the different option of the IVR menu...Then we add 400 ·3905 IP phone to our solution and when a ·3905 call ...
I am trying to lock down a 7945/60/70/75 model VoIP so users aren't able to see the network settings? Can this be done? CUCM 8.6
I use the show line command and it shows:dsx1(slot/unit/channel)=3/0/15, status=VDEV_STATUS_ACTIVE_CALL.VDEV_STATUS_NEGOTIATED.but when i do show isdn status the b-channel 15 does not show as having an active layer 3 call. Is there some wierd number...
Hi all, I'm facing a weird problem and the sip-provider can't help. I suppose there is a problem with the dial-peer/translation-rule but I can't figure it out... There is a CME (c2800nm-ipvoice-mz.124-11.XW10.bin, CME Version 4.2(0)) with a SIP trun...
Hi, guys,I need some help regarding the call hunt configuration. I'm trying to configure a call hunt to pass from one line to the other, and when no line answers the incoming call, the caller is forwarded to an annunciator or a pre-recorded message s...
Good morning everyone!I have a problem with a new deployment of CME that I'm hoping y'all can help me with. We're running CME 9.5 and using Exchange 2013 for voicemail and auto-attendant services. We have a SIP trunk for calls to and from the PSTN ...
Hi everybody,I am working on CUCM v9.1.2 architecture with the following configurationCODEC :- Intra-region 1 HQ : G711/G722- Intra-region 2 RemoteSite : G711/G722- Inter-region 1 HQ / 2 RemoteSite : G729Phones :6945 with SIP + "MTP required" Checked...
Hi Friends,I am unable to start the Cisco ICM distributor service. when I will start it it will show the error message "unable to start the service the service did not start due to a logon failure". Please support.
Hi Cisco techs again,Just a quick questionWhen creating a dial plan for either a small business or residential. Do you need to add the , (comma) in order to get outside line ie 9,02xxxxxxxxAnd with calling mobile phones internationally. You would hav...
Hi everybody, One of my customer has a secure cluster of 2 CUCM and I have to deploy a new CUCM IM & Presence cluster on that installation. When I did the initial installation, I didn't configure any domain name or DNS server, and I know that will be...
Hello all,We have CUCM 8.6 running in UCS.The ova file used before installing CUCM 8.6 on UCS was for less number of resources ( 1xvCPU, 1x80GB, 4GB RAM ).I need to increase resources of VM, so instead of 1=vCPU & 1x80GB, 4GB RAM i want 2 vCPU and 2 ...
We have quite a few SX20's deployed, and updating them manually has proven to be quite a challenge.My question is, if we install the upgrade-specific COP file to the CUCM cluster, do we absolutely have to reboot the cluster in order to proceed with u...
Hi we have a bunch of these 7940 that have lost services like EM and phone directory. i ve tried to restart them but they dont. the only way i found is to physically unplug them and plug them back as we start to have more and more complains, i m thin...
Hi, Shall we use " mls qos trust device cisco-phone " or " mls qos trust device cts "for 9971 phones as they support video calls ? Thanks,Khaled
