Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi We have EM with CUCM 9.1 When one user logged in EM Profile in one Phone, without login out he is trying to Login again in another phone... Then I need to Force logout in Previous profile, how can I do this ? Regds$
Newly setup CUCM and UC 10.5, I have a translation rule on a CUBE that sends all inbound calls to a certain number to a system call handler on Unity Connection. Calls come from a SIP trunk provider. UC is integrated to CUCM using SCCP. The inbound ca...
hi,we implemented CME with Cisco Router 2921 and IP Phones 7962, 7942, 7937, 6921all is running fine - except the time dispaly on the 6921 phones i found a notice on cisco cco... Usage Guidelines Use the olsontimezone command in either telephony-s...
Hi All,I have an issue for fxs port in voice gateway, the fxs port connceted to the fax machine is in off-hook state. it will change to on hook when i unplug the phone cable.IOS Version : C2951-UNIVERSALK9-M version 15.2(4)M5.H323 voice gateway.shut ...
Hi Guys I have a problem, for incoming calls using FXO the call does not get to IP Phones. I´m trying to configure but has been useless.***********Here part of the show run:trunk group SalidaLocal hunt-scheme round-robin!voice rtp send-recv!voice ser...
In the mean time I have to install a CCME (C2911 w/ version 10) in a remote branch with several conference ip-phones CP-8831 on the local LAN that after some months, has to be w/ under/migrated the center Call Managuer. I have check on CCW (to ord...
We are currently in the process of a 7.1.5 to 10.5 migration. On our 7.1.5 system we have the option under MOH sources to ‘play continuously’. This works as we expect in that when more than one device calls for MOH it uses the same MOH stream and doe...
When receiving inbound calls via our sip trunk the calls will not roll over to voicemail, the call just gets dropped. If we call the voicemail pilots internally, or call each other and dont answer the calls go to voicemail correctly. researching this...
Hi,I have two CUBEs in different regions. They both have the same SIP profile and are registered to the same CUCM cluster. We hit an AA in UCX through both CUBEs. On one CUBE the DTMF is working but not the other.The DTMF is being received on the CUB...
I have this single phone that is rebooting every morning. I have done some research and looks like I'm hitting this bug:CSCtj79853 -- memory leak leading to kernel panic and phone rebootsThe bug though, suggests that the known affected release was 9....
Hi,here is my config:cucm 8.5cisco router as gateway to PSTNbunch of cisco and dlink ip phones and CIPCeverything works properly and all SIP and SCCP phones can connect to each other and dial off-net numbers by dialing 9 as prefix.I installed SIP sof...
Hello,I configured a shared line between a sccp VG224 port and a sip 3905 phone but it doesn't work. For sccp I usedephone-dn 15 dual-lineshared-line sipnumber 631 no-reg primary and for 3905 i used voice register dn 15shared-line number 631 both p...
Hi, External calls have no audio and get dropped when using Jabber (softphone or deskphone). This only seems to happen when the User has a video enabled laptop. If we close Jabber the calls are OK. Can anyone help? Thanks Richard
hii have installed java run time and last version of flash while i run CCP as administrator or normal way by double clicking i don't get any error but it's not running and not open but got below messageNOTE:i can't see any process as it says it's run...
Hello All, I have applied new license file on CUE for 80 numbers VM licenses and reloaded the CUE but still showing current 50/80 In active status.even when checked with command show license status application ;50. because of this not able to add new...
