Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
here is my situation.Let say I own 777-777-1111. if someone called 777-777-1111, it'll route to my cucm and I need it to reroute to an external number that I don't own, let say it's 666-666-1111. And if that fails, it'll go to an external number 6...
We are trying to transfer a calls to an after-hours call center. Unfortunately we are getting a fast busy when we attempt to forward. When I run 'debug isdn q931' I can see the reason we are getting a fast busy is the number prefix is incorrect. I...
Is there any more to it than this?Here is the only way to use MeetMe with a 7936; 1. press the pick up handset to get dial tone 2. Press Menu button > Call functions > Meet Me
Good day all,I need to assign an employee a DID number. The problem is that he is in another state and I've only been able to ascertain that our translation pattern is setup for our state and area code. So how would I go about setting up a translatio...
Hi everyone,I am having a problem with remote 7945 phones that have been deployed. The remote connection is set for VPN connection to an ASA 5525. Many phones have worked but I have found that approximately a 1/3 of the phones are failing to launch...
Hello, I am currently using E1 trunk on cisco voice gateway (2911) to connect Telecom. Now I would like to add another E1 trunk as well as another router (2911) to increase outlines and redundancy. I am having two cucm cluster and using H323 between ...
Does anyone have access to CUCM 9.1 to confirm if ring once on active calls works in CUCM 9.1?I have used this feature it in the past in CUCM 7 and 8 just fine. This client is saying this doesn't work and it only beeps when a second call comes in.I a...
Hi,I have tried altering several phones to use a new softkey template, though the phones will not update to this sofkey template, despite applying+restarting, and also physically rebooting the phones!Has anyone seen this? I am not aware of any depen...
Hi Folks,I have a site who is in Rio, Brazil whos cell phones has been changed from 8 digit to 9 digit. In order for me to comply I need to update the dial peer/plan for CME 8.6 . Anyone who can give advice or instructions is appreciated.e.gExample: ...
Greetings to all.i had a problem to establish a voip session between 2 sites as despicted on picture.on site left, i had an 2851 ISR Router with running call manager express, in the other side of the tunnel gre i had an 2801 isr with fxo and fxs port...
I'm using cucm 9.1. I want to give Read only rights on Personal directory to some of my IPT users.How can i acheive this in CUCM 9.1.Regards
Hi,does anyone know if its possible to syncronize call-lists (placed calls, missed calls etc) between phones sharing the same line?Regards, Frank
Dear all. We have cisco CUCM 8.6 and C2951 router for GW. It was working perfectly before. But today when i call from outside to CUCM, it says "Number you have dialed not exist" (unallocated and unassigned number). But Telco says there are no problem...
Hi ,I am facing issue with my outgoing calls, i have configured mgcp on the remote location with my call manager 8.6.I am unable to dial outgoing number but my incoming numbers are working fine. Please help me on this.Please find below the debug isdn...
Hi everyone. We have cisco CUCM 8.6 and C2951 router for gateway. We also have E1 for the telco line. It worked perfectly before. But now it can't call outside from the CUCM and also can't call from outside to CUCM. When i call to CUCM main number (t...
