Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello allI am currently build up a Voice lab using GNS3 + VMware. Laptop OS: windows 7 (64 bit). Topology is as below:PC loopback 192.168.100.200 is binding with NIC of Cloud in GNS3, NIC of VMware based CUCM is working in bridge mode.In order to run...
Hi,I'm looking for a vendor that prints the co branding lables that go on most of the IP phones. See image below.Anyone know where i can get these printed up?Cheers
HiI have installed CUBAC 9 and CCM 8.5All Route points and ports have been configured with a CSS that has access to all endpoints.When I try and do a blind transfer from the console the endpoint rings but when I answer the call just drops.If I do the...
CUCM - most recent release:CUBE will be on 29xxWe were planning to enable T.38 for Fax on a VG224 analog gateway under MGCP control. For various reasons we may not be able to use the Carrier we had been planning on that supported T.38 on SIP Trunks,...
Hi AllI have problem in NTP server I configured my Domain server as ntp server when add the ntp server in the cucm 7 Pub by ip of my domain server (192.168.1.7) the status showing "The NTP service not accessible".I login the ssh to the call mamager...
Dear All,I need to install meeting place 8.5 on UCS C220.Kindly guide me the procedure for the implementation.I will be very grateful to you.Regards,Malik.
I have a problem . this is the first time to install CME-BACD . when I finshed the instllation there are an error apper :Oct 24 06:55:46.027: //3//TCL :/tcl_PutsObjCmd: TCL AA: +++ B-ACD-SERVICE not registered, Starting B-ACD-SERVICE +++Oct 24 06:55:...
Hello, can someone please give me a couple of examples of the purpose for dividing ISDN timeslots up into DS0 groups.Apart from allocating some timeslots to voice and some to data, what other reasons would there be ?Thanks for any help.
Hi everyone ,1-could some one help me with documentation or configuration of cucm to support miarec recording software?what are the steps needed ?2-Also i read about span configuration on the switch ports,What if i have both CUCM and Miarec running o...
Hello All,Maximum 3 call managers can be added in CM group and one SRST reference. So totally 4 CM servers but why we have CM server 5 in all cisco phones under network configuration.-Murali
Hi,I have one site configured as cme and rest all the sites are registered in one cucm. Now transcodoing, conferecing & MTP configuration on cme router would be poiting to cucm or would remain for only local phones in cme.voice-card 0 dspfarm dsp ser...
Hello All,I didnt get proper doc for this. Why we have Custom tab in RTMT tool (Check attachment), is that to configure new alerts apart from predefined alerts in RTMT. If yes, please let me know how to add new alerts in RTMT under custom tab.-Murali
Hi,I am new to this scripting and tcl world. I just want to know the actual use of this BACD and AA. Since we have CUE then why and where do we use?Lets say my incoming calls listen to musci from CUE where i have configured AA and VoiceMail then stil...
Hi All,I am trying to build a Voice lab and it's starting to cost a fortune for the kit.I have seen a T1/E1 cross over cable on the link below and I need two of these from my set uphttp://www.ebay.co.uk/itm/UTP-Voice-data-T1-E1-Cross-Crossover-back-t...
Hi,Can any one help me to sort out this problem, I can not login to my Publisher either in GUI mode or CLI mode,If i try to open in GUI mode, it is not responding at all.In CLI mode, after entering the user name, Password prompt is not showing at all...
