Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, I'm have Cisco IP Phone + Cisco Switch + Cisco Router + an SIP account release from ISP (internet service provider).My topology: Cisco IP Phone => Switch => Router => ISP..............But I can't calling from inbound to outbound and from outbound...
Hello, we are installing a new SIP trunk from our ISP to replace our PRI. With the setup the way we have it we are getting ring no answer on inbound calls and fast busy on outbound calls. The ISP has a Cisco 2900 router that is NATing over to our C...
hello everyone, Since and that I need to record calls in UC560, that steps are.Some reading?Regards. Thank you.
By default, our LDAP-imported users have the "Enable User for Unified CM IM and Presence" checkbox disabled. We'd like to have this enabled by default. I seem to remember that this was possible in CUCM 8.6.2 with CUPS, but it was a setting in the L...
Hi All,I have this scenario:CME 8.6Web Server Security Surveillance SystemCisco 7975G PhonesThe Web Server contains a XML Script that shows the snapshots from 8 different cameras.From every phone i can get to Services and choose Camera Viewer and wor...
How would you or can you enable web access enable a phone on a Call Manager Express? So on CUCM I would select the phone and on the device settings pick Web Access Enabled. This allows me to ip to the phone and retrieve things such as QOS. But No...
Hello, I have a 7965 phone that has 3 extensions configured on 3 seperate buttons. 1. x12345 is on button 1 and is the primary extension for this phone2. x12346 is on button 23. x12347 is on button 3 (this extension has an appearance on multiple diff...
Добрый день, как настроить стоимость звонка в CallManager 9 .заранее спасибо.
Can I do 4 digit dialing between a UC540 to a UC320W that has a point to point circuit? If so are any licenses required? Also can I do 4 digit dialing even if its a VPN connection between the two?
We have been given DID's that do not match with extensions at all. Example last 4 being 2344 - 2368 on one group of the DIDs where we need this going to 2300 - 2324. Is there an easy way to translate these numbers. Below is how I have it configure...
We are currently in the process of moving our Call Manager and voice gateways to an off-site data center. However, one of our gateways has a 2 port fxs card we use for our fax machine. The fax machine is, of course, staying in our offices. Any ide...
Hello,For example, we have CUCM 9.1 and 2 divisions: - Division1 with Network_Subnet1 and extensions 1XXX - Division2 with Network_Subnet2 and extensions 2XXXHow can I allow registration of phones with extensions 1XXX (or Device Pool DP_Div1)...
Hi Guys,Can someone please help me with the following BAT issue in CUCM 6.1.2*****************************************I am trying to update the “call waiting busy trigger†and “Call Forward Busy†for only those UDP's which has line 2 starting...
Hi, We have CUCM 8.6.1 and we have strange problem. On some phones and some Directory Numbers, when we push New Call Button on phone and Dial Directory Number, phone doesn't ring about 7-10 seconds and then rings. But if we dial another directory num...
HiWe have cucm 9.1, we have IDD route pattens with FAC enabled, I noticed that there is a long delay when dialing IDD numbers, CUCM route patten 00!, in the VGW dial-peer has 00T, can we adjust this waiting time ?can we adjust waiting time after ente...
