Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
HelloI am trying to create a passcode for 1 IP Phone in a Network and have the following configuration in place as shown below:The plan is that when this IP Phone wants to dial out they will have to dial out the a 4 digit number 5798 followed by the ...
Hi,I have a CUCM 8.6.2.21900-5 and I'm noticing that the CDR records generated have a issue with the finalCalledPartyNumberThe finalCalledPartyNumber is not correct when the call is answered by another number.For example if an extension 7800 is call...
Hi, We are planning to change the numbering plan of our CCM cluster. Currently the numbering plan was based on the employee number which is 4 digits. We are planning to change it to six digits. We are having three locations. Location A will be having...
In CUCM 7.1 as I can block the exit to a specified number of pstn?
Hi All,Working towards me CCIE Voice Lab exam.....I have 3745 Router with:1 x NM-HDV3 x PVDM-121 x VWIC-1MFT-E1 Module.1 x 7960 PhoneI have placed a Loopback cable in the single E1 socket, but I get "RX <- BAD FRAME" received when debug isdn q921 is ...
Dear NetPro gurus,I have a brand new Cisco 3945 CME router on a customer site. However, when i checked the license, it says the CME-SRST will expire in 58 days even though i have the following:-- Uck9 as Permanent License- I also have the FL-CME as ...
Hi,When i try to login to publisher its very slow to display even the adminisration page.subscriber is working fine.I check the cpu and memory utilization its also fine.Try to login to different pc the result is sameAny body facing the same issue
Hi all,I am faced an issue which all my phone get failed to register (unable to see the ip address of the phone in the administrator page) once i upgraded to cucm 8.6.2 from 8.5.1.But from the phone itself, i able ot do a access into the cucm page. F...
Dears, Everything was fine with my cluster of two VMs with version 8.6 installed on UCS server.After one week, the customer asked to change the password for all the users, I logged in to CUCM administration page, and here is the surprise, I didn't fi...
Hi Every one, I am configuring an e1 on a 5850 that has 24- channelized E1/ PRI port, I have 1 E1 conencted on a DMS 100 Nortel Switch where we get all teh PSTN calls, the problems is that we need to get the Calling number (ANI) on our 5850 so that...
Hi,Are there any known restrictions with FXS ports with IOS 15 on voice gateways? I have a fax machine plugged into a fxs port on a 2901 router. When I make an inbound call, the call connects straight away to the fax. However, when I attempt to send ...
Hi guys,At my work place I have CCM 7.1 & ICM 7.5.I have a domain user ("installuser") which was used in installation & sync. It is currently used as RDP user to manege the servers.Due to security reasons I have to change the password of this user.Is...
Hi, I am baffeled I am trying to run VOIP traffic from an elastix server over a Cisco 870 router. Call quality is fine untill more then a few people start surfing the internet. I have tried to enable some QOS on the router but with it I can make one...
Dear NetPro gurus,My customer has a new CME (with CUE) and they tried to call the CUE x82299 via SIP Trunk from CUCM's phones. However, they keep on getting fast busy.The debug as attached.All calls to the phones registered with CME has no problems ...
Hi Guys I need your help for a heavy problem I have with my Cisco SPA502G Voip Phone. After a Firmware Upgrade my device is in auto boot loop and I don't have any chance to login to the device or enter in the configuration menù. I absolutely need a h...
