Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, community!I have a question about licenses for 3905 phone to use with CUCME.Is there any license I need except FL-CME-SRST-25 for 2901 router license to support 3905 (p/n: CP-3905= ) phone?For example, for 7911G phone (p/n: CP-7911G) you need...
Guys,Can you help me, please .... maybe you have hints ...I want to active ipphone authentication to CUCM with CTL, but i don't have any experienced with CTL.my question is first, can i check ipphone authentication and encrypted status in CUCM or ipp...
Hi all,I'm having an issue where i'm tyring to setup different codecs for a group of phones where bandwidth is at a premium. I'm trying to convert them over to use g729, but am having some issues. Our main codec is g711u. I created a new region and d...
We are using CUCM7.1(3), and try to integrate a fax server in the CUCM, call flow like this Fax server->CUCM trunk->h323 gateway->fax machineWhen we do the debug isdn q931, we can see the call was setup, but after a while(around 10 seconds), the call...
Hi,We've been issued with the following 2 license files for a CUC cluster upgrade to version 8.6.2:UNITYCN8-HA-PAKUNITYCN8-VUP-K9Please could someone confirm to me which mac address I use when licensing UNITYCN8-HA-PAK.I've read that it is the subscr...
Hi,We have installed Cisco 2901 router as CME for one of our customers. This will be a dedicated CME serving near about 40-45 phones. There will be no integration with CUCM or any other UC devices. All phones are registered to CME. Attached license f...
Hello,This is probably a pretty basic question for this forum but I don't know how you do this. Can someone please advise how I would go about to set up configuration backup via FTP for CUCM 8.5?Thanks,Adil
How do I display the full software version? I'm only familiar with the linux based systems. Thanks!
Hi all,I would like to have a copy of hard drives of my CUCM 6.1.5 for store it in another place.I found this article related to CUCM 7.1.2 where is indicated the procedure to change a failed hard drive: http://www.cisco.com/en/US/docs/voice_ip_comm/...
Hi all,I'm looking for your help about a problem I'm experiencing on a customer site.I configured a SIP Trunk with a "virtual" destination ip adress that load-balance to two "physical" ip adress (for a fax server cluster).Since I do that, the outgoin...
Hello,Our ELIN numbers are getting "wardialed" on a regular basis. The call gets routed to CER, but there is no 911 match. The call then gets routed to our onsite police through the onsite alert setting (And are getting pissed). When there is no 9...
Hi All,Im new to Visual voicemial. Most of user in my site are facing the problem in visua voicemail. When i was looking into this issue i found that the file ".jad" is not downlading and getting the below error intermitently. Sometime im able to dow...
Hi,I have CUCM 7.x in HO and SRST in branches. The communication between the sites is via G.729. Centralized call processing model is used. When we try to conference between sites it does not happen. We are not using any hardware conference bridges a...
Hi,I have call manager 8.5 installed and a route pattern that route all calls to the gateway. No restrictions. I can make local calls , international calls and calls to mobile phones but I can't call 5-digit numbers. I get external line with 0 and wh...
When I ping from local router to IP phone the situation is like this:<font color=red>Sending 100, 100-byte ICMP Echos to 10.1xx.x.x, timeout is 2 seconds:!!!!!.!!!!!!!.!!!!!.!!!!!!!.!!!!!.!!!!!!.!!!!!.!!!!!!!!.!!!!!.!!!!!!!!!.!!!!!.!!!!!!!.!!!!!.!!!!...
