Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We have actually a CUCMBE system in production. The end users were created with LDAP server. We need to remove LDAP sync and Authentication.We would like to keep all end users in CUCMBE local. We try to remove it with many process and nothing worked ...
Hi,We are currently planning to implement 20 seat phone system for testing purposes and in next 12 - 18 months we will look to expand it to min 300 seats (we are IT department for pretty big (10 offices & 350 staff) company). We currently have C2921 ...
To preface, I am a total novice with CME. Now that that is out of the way....I have a Viking single push button intercom and Viking remote touch tone relay controller that I need to somehow interface with our CME. Functionally, the way this should...
Have a customer with UC 8, 4 sites including main site. running MGCP at remote sites and h323 at main site. Site A = main site. If user at Site B forwards their phone to an external number and someone calls that ext from another remote site, not t...
I just implemented "Mobile Connect" on our CUCM 8.5. (We use h.323 gateways, and PRI's.) It seems to be working correctly: if someone calls an internal line, it rings both the IP phone and the cell phone. I can answer it on the cell phone and it appe...
I have this error on seven of my subs (Unable to contact server. Master or Local Agent could be down). I have check my Pub and Subs in the network services Local DSR and Master are running and activated. Cisco 7.0 Unified Communication Manager. I wai...
My client has a CUCM 6 cluster with 500 phones configured for the auto reg pool (1000 - 1500). The pool has been exhausted - in that the highest number has been used (DN 1500). However, lower DN numbers have been freed up. It does not appear that ...
Hi All,I has had problem to registering ATAS 187 on Cisco 7.1.3, and after looking on the Cisco Support Page I found that there is a QED File and Firmware for Version el CUCM Above 6.XJust look at this link.http://www.cisco.com/web/software/282074215...
Hello All,Looking for some help. I am working for the first time on setting up an eSRST/SRSV solution at our remote site. We are using:- UMG ver 8.6 (eSRST & SRSV)- Communications Manager Cluster is 7.1.3- Unity Connection 8.1- remotes are using ISR ...
I have a 2901 router with a EHWIC-D-8ESG-P card in it. I have configured a DHCP Pool for the voice vlan but the phones get an IP address from the data vlan. What am I doing wrong..,?ip dhcp excluded-address 10.2.100.1 10.2.100.30!ip dhcp pool Phonesn...
Is SRST possible when using CUCMBE6000 on a single site? Suuuurely?! Tell me I've been advised wrongly...
Hi guys, Currently we are deploying a CUCM solution, but on the customer side we are thinking in put a CME-SRST CPE, for this purposes the phones on customer side will register on CUCM but in a case of a WAN failure the local CME will act as SRST and...
We've decided to move our Publisher to our Data Center. It was originally designed as a single-site deployment, but Management liked it so much, they want to roll out more subscribers at remote locations and bring the Publisher home.Does anyone have...
At our hospitals, our nurses use 7925G's as phones and message alerting systems for monitoring patients.Their biggest complaint is that, when they're on a call, the "staff assist" or any type of nurse call messages are very loud. (which they are)Can...
Hi there! I recently got a request which will require a hunt group configured in a particular way and im wondering if you can help me out. I am currently running Cisco Unified Call Manager Version 6. Is it possible to individually set the ring time ...
