Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all, I working on a document that explain what is available when my publisher is down, and when I am only running on my subscriber (both of the servers have the same services activated, and it is CUCM 7.1.5 version).From the SRND 7.X we can find t...
I`m trying to configure two clusters connecting to a single Unity Connection 2.1. I`ve set up ICT from cluster B ( New cluster) to CUC- all good , calls being delivered to the correct main box however MWI failing. From the new Cluster I can dial the...
Hi all,I trying to findout exactly what this message means:%FLEXDSPRM-3-TDM_CONNECT: failed to connect voice-port (1/1/0) to dsp_channel(1/1/1)Aug 2 13:31:18.428 BRA: %FLEXDSPRM-3-TDM_CONNECT: failed to connect voice-port (1/1/0) to dsp_channel(1/1/...
Hey all,I have not programmed voice in years and I am programming an AS5400 as PRI.I setup the primary D channel just fine but when I try to do the backup D channel it gives me this error:CCT_ATT_SE_VOICE#conf tEnter configuration commands, one per l...
Hello,Have some new 9971 sip phones with CKEM expansive modules and CUCM 8.0. On the phone configuration mode i've seleceted CKEM and 9971 phone uploaded the firmware form the CUCM.But when i try to insert it into the phone (side USB option is enabl...
Hi gurusAs Calling Number Globalization is introduced in 7.0 is there a way to put "+" (plus sign) in "From" field when calling out over a SIP trunk?
I've created a backup Extension Mobility service in CUCM 4.3 and want to subscribe this service to Device profile of almost 900 users. How can i do this using BAT.Regards,SJSJ
I have detected a problem in a location that has available bandwidth but in RTMT is out of resources and the client can't make calls.There were 2 active calls, but in the RTMT the value of tha available bandwidth wasn´t the reflection of 2 active cal...
Dear all,Does anyone has any documentation on how I can create normalization rules for integration between Lync and Cisco Presence?? The document I found called "Configuring Cisco Unified Presence Release 8.5(2) with Microsoft Lync Server 2010 Standa...
Hello All, I am looking for a help on DN based TOD. TOD documents talks about 1- Conf of Time Period2- Conf of Time Schedule3- Conf of Partition4- Conf of CSS5- Then assign the PT in to transformation pattern.This will enable CUCM to check the time a...
Kindly note that the deployed phones are dual line mapped with a 3 digit extn and a DID number. now if some one calls on the mapped DID numbers the call lands up on the right extension, the issue is if some one from internal calls up the outward num...
One of my remote sites running CME 7.1 and CUE 3.2.5 on a NME on a 3825 ISR is having the following issue.there call park is only working intermitently, some calls that get park are just dropped, others once its parked no one can pick up the call exc...
I have a Cisco Dual Profile 52(C60 codec). I tried installing the Touch 8" it comes with. When I power it up, it can see and recognize the C60 and when I click on Start Pairing, it downloads a new software but failed on extracting it.Touch will sho...
Hi,I'm willing to get get the call log from amc performance log.I want to get logs for a month, but they are held 9 days only, former logs are not shown.How can I get longer the logs to be collected?Thanks in advance,Yasuyuki Hirasawa
I am trying to setup a cisco unified sip proxy (CUSP). I am unable to access the web page of CUSP.I have ip http server command on router with local authentication on.Thanks in advance
