Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Is the 8 port pri strictly for data?
I am trying to recover a crashed CUCM that has no usable config file. How do you get Unity to act as Auto-Attendant and pick up calls to DiD's that CallManager routes?
Hi,I start to configure MGCP for fallback, but each time I try to test the fallback outside calls are getting busy signal.here the configuration :!boot system flash:c2800nm-spservicesk9-mz.124-24.T.bin!isdn switch-type primary-dms100!voice rtp send-r...
Dear sir,I am using CUCM 7.1,at the reception I have configured the hunt on 3 cisco 7965 IP Phones with 7915 expantion module,I have configured call pickup on these 3 phones,Butcall pickup is not working while Huntingso plese give me the solution for...
Hello,I hope the community can ive some good advices or/and direction of seraching the information.We're using currenty an Opensource SIP platform (Openser/kamailio + Asterisk) for switching the VoIP calls, the PSTN gateway are doing for us external ...
Hello all, We plan on upgrading our CUCM cluster to version 7.1(3b)SU2 from version 6.1(4). We currently run 1760 voice gateways with the IOS: ‘c1700-ipvoicek9-mz.124-15.T9.bin’ (12.4T range). I wanted to establish if the latest version of this IOS w...
Hello to everyone,Would be great help if anyone guide me to find out SCCP version in CUCM 7.0 ?regardssiva
Dialling from Cisco UCM environment to Tandberg Video environment. Need to be able to convert from E.164 to SIP URI so that the call can be completed. Cisco SIP Proxy Server?Any guidelines on best practice/deployment strategy/Install guide?
Hi, I am running into a weird issue with the Cisco 9971 phone. We have it setup in a test (evaluation) environment to test against call manager 8.x and other systems as well. We managed to get the phone to register correctly everywhere, however we ar...
Hi,I have installed a new Cisco Unity Connection earlier today using OS 7.1.3.30000-1.When l login into the CUC Administrators page, CUC show that l am running OS 7.1.3.10000-68, is this a bug? I would have thought that all OS levels would have been ...
Hi Guys,I'm building a Business Edition server that shipped with 7.1.5-10000-12Is this a stable version or should I be going to later release??Thanks in advance,Neil.
Hi,I am facing an issue after integrating PBX with 1860 Router. When a call comes in from PBX extension to a phone connected to Router (For both IP Phones and also Analog Phones connected to FXO), the phone keeps ringing even after the Caller hangs u...
Hi,I have installed 2 server Call Manager version 7.1.3 (Publisher and Subscriber).I want to configure Extension mobility in failover using server Load Balancing (SLB) as recommanded by Cisco.I want to know which type of server can I use for SLB? bec...
Hi all,I want to integrate a CUCM 6.0 with a Siemen Hipath 4000 PBX. The router is a 3845 router and is already configured on the CUCM using h323 protocol, but not integrated with the PBX yet.I have two questions: 1) Is it true that h323 does not wor...
Hello there,Following my precedent request, I need advises about the better router I can choose for this architecture:CUCM ----- [GW] ----- MGW Alcatel ----- OXEThe control proto are these:CUCM --|MGCP|--- [GW] --|QSIG|--- MGW Alcatel ----- OXEAnd se...
