Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
HiI have registered a 7936 conference station on my UCM 7.1The conference station registered but the softkey is not active.Appreciate your supportThanks
Is there a way to bulk add FXS ports on a 3845 voice gateway?
Hi all,I'm having problems finding out wether Unity 2.46 and CCM 4.3(2) will work together.I'm currently using Unity 2.46 and CCM 4.2(3) without any problems.Has anyone out there used those two versions together and how did it go?Can someone point me...
Guys - I really hope I'm not being really thick here (but its possible!) as I have done this lots of time in the past, but has anyone had issues upgrading to 7.1.3.32900-4 using the joined UCSInstall_UCOS_7.1.3.32900-4.sgn.iso file? I am upgrading f...
Hello All, I'am trying to integrate a Bogen Multicom with our phone system. We have a 2851 and a Valcom V-9970 that goes to the Bogen and connects to our 2851. I have it connected into an FXS port and I'am using the pattern 31..., They di...
I get the following error in my DMAErrors.log.***> DATA PROCESSING TESTS REVEALED AN ISSUE WHICH GENERATED THE FOLLOWING EVENT: The error number is: [-691] The error message is: [-691 Missing key in referenced table for referential constraint] Th...
Deer All ,Is the CDR in CUCM 7 has same limitation of CDR in CCM 4 only 100 record ?best regards
Hello.We are trying Cisco scripts app_faxmail_onramp.2.0.1.3.tcl and app_faxmail_offramp.2.0.1.1.tcl for T.37 onramp (incoming, fax2mail) and offramp (outgoing, mail2fax) faxes, respectively.Incoming faxes work, but outgoing faxes have some problems....
Hi GuysI have a issue with calls coming from my Siemens PABX to my MS Exchange Voice mail system.My setup is as follow,CCM ver7.1.3Exchange 2010Siemens PABXMy PSTN is connected to my Siemens PABX, The Siemens connects via 2 Qsig trunk to my CCM.I hav...
I can not get my 7914 to show any numbers. I am using 7965G phones with 7914 expansion modules. I am using ccm 4.1, I have the SCCP firmware SP00105000300 (cmterm7914-sccp.5-0-3.exe) loaded on both pub/sub. The phones are using SCCP45.8-4-1SR2S. T...
Hi All,we have sub and pub in two different sites. Bandwidth in sub site is much higher than pub site. I like MOH to play only from sub site for all remote sites and only play from pub site if call being on hold locally on pub site. I haven't created...
From the perspective of hard wired telephones the Cisco Emergency Responder is pretty cut and dry.How have you all handled portable wireless telephones like a 7921 ? Right now in my CER they show up as unallocated. Since they can travel building to ...
Hello,I'm trying to determine how the Communications Manager System Version matches up with the Version labeled on the Installation DVD. For example, in my CUCM I have a system Version of 6.0.1.2000-3 and I'd like to make sure I have the correct ins...
i need to conect two CUCM using a couple of CUBE, but when i test the config i receive a disconect reason 47, do you have a document to do this or if you have some experience to do this, please let me know, the reason to do that is because we need to...
Hi Guys,I just wondering, which IP address on RouterD should I include on "session target ipv4" if for example:RouterA would like to call RouterF, how do you direct the call to using the "PRI link" on RouterB >> RouterE >> RouterF? instead of going t...
