Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
In Cisco Call Manager Serviceability, I can monitor “calls in progress†under “Call Process†“ Call Activity†which appears to show current number of calls in progress at a given time.I am attempting to locate a way in which this informat...
We are reaching out to our local carriers to see if RDNIS service is available. Right now in the event our MPLS links are oversubscribed all voicemail calls will re route to the location receptionist because we could not get RDNIS to work all the wa...
Customer wants to convert Cisco Unity 5.X UM with an off box message store running Exchange 2003 to Voicemail Only. I am looking for specific instructions. I'm sure this can be done but have never performed this.
Our company wants to push out a speed dial (new conference bridge number) for all existing Cisco phones. Without exporting the phones, editing the .csv and importing them back, does anyone know of a way to do this? (Two clusters: 6.1.2 & 4.1.3).
Greetings,We are running a CM 6.1.2.1000-13 BE system and just started seeing the "High Traffic Try Again Later" message appear on the display of a few phones. In one case the call was dropped as well. Checked all the logs on CM as well as voice gate...
Hey Guys,I wanted to confirm if the DTMF activated mid-call features are available to Remote Destination devices in SNR when 'not' using the Mobility Voice Access feature (Dual Stage dialing)?Thanks guys,TF
Forexample, now I have Router Pattern like810.X! for international calls and 80XXXXXXXXXfor intercity calls.Now, my National provider change International numbering plan to this:Access code for international calls - <b>00</bAccess code for intercity...
For some reason I am missing a lot of features when using the Voice side of my router. There are more commands missing than what I have listed. I listed a couple below CUCME 4.3 ((C3745-ADVENTERPRISEK9-M), Version 12.4(25) 1. I have a 7906 and I ...
Hello, I'm trying to write a query against CUCM6.1.2 that will give me all calls made to an extension for an inclusive range of dates. I want to say give me all calls made to extension "Z" for an example between September 9th and October 1st.Here is ...
Hi, I have a scenario where the phones are in SRST mode, a call from the PSTN will not trigger the voice mail pilot and neither will a internal call. It keeps ringing. I configured the following: Call Forward,busy, no answer internal external - check...
Dear All,I am trying to change the default numbering plan from NANP to UKNP.I have installed the locale file "cm-locale-en_GB-7.0.1.3000-1.cop.sgn" twice from the below location from CCO and rebooted the server. Voice and Unified Communications >Cisc...
Hi, I have very limited info but I'm looking to point someone in the right direction. My colleague has the following setup in Europe. Cisco Call Manager version 7.1 with ISDN trunks to the PSTN. The Call Manager has SIP trunks to an Aspect Call Ce...
Hi all,i would known if cucm business edition support high availability feature:Is possible to make a 2 cucmbe cluster with cisco unity connection?RegardsDiego
Hi,CUBE is installed between CUCM and Carrier SIP Trunk and want to the firewall feature requirement in case the firewall install in front of CUBE to protect from Carrier.If the firewall is Cisco ASA, I can enable "inspect sip" to inspect the payload...
Have a CME (4.1) system I'm setting up on a 2821XM with Unity Express CUE (3.1.1). GUI works great for setting up mailboxes, calls transfer to VM ok and get greeting on CFNA. The problem is that when a user tried to set up their voicemail they can he...
