Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello everyone,On a setup that will use 2 PRIs with the hunt group set up to use both PRIs for access to all 46 channels is there any reason for setting 1 PRI B Channel selection for low to high and the other for high to low or does it make more sen...
I have an issue when opening a browser window to my subcriber https://ukldnccm01/ccmadmin I get the following message "The name on the security certificate is invalid or does not match the name of the site" I checked the certificate on the cucm6.1.3 ...
hi,we are using cisco unified call manager 5.1 with 7911,7940,7961 and 7970 phones.is it possible to change the cisco logo displayed on ip phones to our company logo in a single steps.i mean there is option on phone to select the logo from the list.i...
Hi,actually I'm trying to configure Mobile Connect on BRI Ports, I know from this document, that it does not work:http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/srnd/7x/mobilapp.html#wp1043943Having a look on the MGCP controlled BRI port:May 12 1...
Dear sir ,I have three location A ,B and C , we are using cisco unity 5.0 and callmanager in central site (site C) as a centralized model .remaing two remote locations are connected on central site. In (remote site A) we have FXO and in Remote locati...
Hi all I have a two sites that are connected via a 100Mb metro E link. Each site has about 40 Cisco VOIP phones with about 5 Fax machines at each location. I keep getting compalints about Faxs dropping on a regular basis. I deployed the access switch...
Hi,I have a ephone-dn with dual-line, when the first line in use, the second call came into the same number. If I put first line on hold, the second line will be automatically answered.Can I just let the second line ring, but still put the first line...
Hi all,I have the following problem:my uc520 uses a SIP Gsm gateway for incoming and outgoing gsm calls.We have no problem with outgoing calls, but when we receive the incoming calls it behaves wrong.The incoming call is correctly forwarded to the in...
Hi,I have ordered the CUWL Professional Edition with MP7.0 and when I complete the configuration, the configurator gives me MP-70-UL-UWL with 40 Ports for 1000 Professional Users. I would like to clarify whether MP-70-UL-UWL of 40 Ports is applicable...
To display a custom image on Cisco phones with CME - you need to be specific in formatting the image and place in in a specific spot in flash. I am having problems copy the image to that Desktop/320x212x16 directory. What's the mojo to get my png a...
We have 3560 switches -almost every port is set to "switchport voice vlan 2" and our data vlan6.If I apply a "switchport mode access" to the interface will it break one of the vlans?Thanks,Andy
I am having incoming calls to one specific DID number dropping. Below is the Debug ISDN Q931Any help would be appreciated Progress Ind i = 0x8088 - In-band info or appropriate now available Feb 15 08:36:46.324 EDT: ISDN Se0/0/0:23 Q931: RX <- SETUP p...
We have 2 CUCM 6.1 systems in the 2 different cities (A and B). These 2 systems are connected for 4-digit dialing via ICT in MPLS network. We just found out today that the call is disconnected in about 5 mins when you are on the phone between phone...
Hi,im trying to build a cme with a few sip phones and sccp phones...However there are two sip phones registered and one sccp phone..i can call from the sip phones to the sccp phone but not the other way..it's also not possible to call from sip to sip...
I am working on some afterhours autoattendant scripting, which was supposed to be simple and straightforward, but which has turned more complicated. The biggest issue right now is trying to figure out the ins and outs of voicemail notification to pa...
| User | Count |
|---|---|
| 9 | |
| 4 | |
| 3 | |
| 1 | |
| 1 |
