Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
HelloWe have CUCM v12.5 and UCCX v11.5 in our newly deployed HQ.All phones in HQ are registering to the CUCM_Pub. 3 phones need to place in another branch which is connected to HQ via WAN (VPN) but when we take phones to the branch site they are not ...
I am planning to upgrade the VG224 to Version 15.1.4M10(MD) and I am confused which IOS below I need to download. The current IOS version of the VG224 is 12.4(22)T5. (flash:vg20x-ipvoice-mz.124-22.T5.bin). Can anyone explain me the difference of two ...
Hello all, I have a customer wanting to migrate some 7941 from SCCP to SIP.In bulk i created the Phone Template and tested the migration. The phone linked to a "classic" ethernet port.However, this customer has dot1x enabled on every switches interfa...
Hi all, There is a 3800 router with fxo port registered as voice gateway. The problem is when there is an incoming call to a phone line connected to fxo port , there is a delay in transferring the call to IP phone. The caller hears 10 ringsand only a...
Hi, Is it possible I can use cisco ip phone as pa system . If I dial a number and , its can connected to a speaker .... Thanks
Dear Friends I had a cisco router 2951 with cme 10.5 installed. I want to use this router as sip and sccp phone service everything is ok, but I had one problem that I had a voip gsm gateway (4 sim cards) and I don't know how make configuration t...
Hello Community,we switched from our PBX to SIP Trunk. We have a CISCO 29series (without CUBE). The router interface is directly connected to the Internet with a public IP address. Unfortunate we cannot register our SIP Trunk to the ISP. What did I w...
I have a strange behavior in my site. from my information outgoing calls over E1 has a pilot random technique and didn't need exact calling party transformation mask on route pattern or EXT Phone number mask on DN to route successfullybut in my site ...
Hello, I have a SIP trunk from my Service Provider (STC- Saudi Arabia). ITSP<------>CUBE<----------->SIP<--------->CUCM Cluster I have some problem during the call forward. Some calls are being forwarded without any issue: 1) A call from internal ext...
Hello,I use a Cisco SPA112 VOIP box, connected in Ethernet, on a router for several years for my phone line.I would like to move my phone away from my router (I will not be able to use a long ethernet cable) and connect the SPA112 with a WIFI Etherne...
Hello, I am using a cisco 2921 router that has cisco 12.1 and I am trying to run the ccp and cme gui's I keep getting this webpage that loops and nothing else. See attachment.
I am use ProTech voice gateway integrate to our cucm ver 11.5. Now the outgoing call from cucm to mobile through voice gateway successfully done. We just add the sip trunk with route Pattern and non security profile. The issue in the incoming call f...
Hi, I have a Cisco 8851-3pcc hooked up with a Plantronics CS540 and a APU-76 cable (USB). When I answer a call, switch from handset to headset or simply dial a number with the headset I have to wait around 8 seconds before audio is enabled on the hea...
Hi everyone I appreciate any help you can assist for this. We purchased 3 Cisco 8861 phones for our VoIP with the service carrier RingCentral. The phones are currently connected through our wifi and not an Ethernet line. We purchased the Planitonic...
Hi Guys I have a issue with the DNS: In the CUCM web admin, it show WARNING: DNS unreachable. I have the follow tests: Starting diagnostic test(s)===========================test - disk_space : Passed (available: 1207 MB, used: 12475 MB)ski...
