Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We have one subscriber of the 4 sub in our cluster that has occasional high CPU and we go into Code Yellow. Started about a week ago. Happens about 10 times during the business day.All subs have about the same load with number of phones/gateways, s...
Hi all,Why my 7970G is displaying wrong time while all others are with the right time?I'm using ccme4.2, the load file on my 7970 is SCCP70.8-2-2SR2S, my ios is 12.4(11)XW2.I've set the time-zone parameter on telephone-service.This issue is driving m...
hi we have a centralised setup of ccm 4.2(3) and the ip phones are in different cities,we also have a trunk to USA also.i have blocked offnet to offnet calls for the external transfer to PSTN.But as the PSTN line is connected to the central site gat...
Hello there.Suddenly, for no apparent reason, no-one can CFwdALL! They can add a number (via IP Phone or CCM), and this displays on IP Phone. But if you call the DN, it just rings.Help!
Should progress_ind always be configured in dial-peers with h.323 gateways? If not, when should progress_ind {setup | connect | progress | alert} be used?Regards
hello, i have Cisco call manager connected to PBX via 2811 through VIC2-2BRI, the problem is sometimes the outgoing call does not pass and when i make trace, it displays what you will find in attachement.you will also find in attachement the confgiur...
dear sir, Anyone have installation document for the subject mentioned device? What's the feature we can implement on the device? Please advise. thanks.
I have a customer that uses extension mobility, they have 200 users with device profiles, they want to update the profiles with a soft key template change, i cannot find a solution to update the profiles. You can add, delete but there is no update op...
When pressing "Corporate Directory" buttonthe message "XML [4]: Parse Error" appeared.When using the previos version of IP Communicator 2.0.2 I have no problem withit and config of my CCM 4.1.3 wasn't changed since than.
Hi,I need to configure AAR in one of the UC labs. I have a question here regarding the Dial prefix. There are two dial prefixes.One from this group another to this group.I am not sure whats the use of Prefix(to this group).For example I have two site...
CCM 4.23 SR2b, 7961 FW version is SCCP41.8-2-2SR1S. H323 gateway 12.4(8c). Some phones mysteriously get stuck in CCM fallback SRST mode and do not re-register with CCM even though WAN is up. Only thing that gets the phones back is to cut the power ...
Hi All,after doing thisStart > Run; type CCMPWDChangerwe were able to logon, and also to able to change the password, now even after restarting the whole server we can logon Start > Run; type CCMPWDChangerand we are not able to log on, but the appear...
Hinow i dont' reveived and send call's from CCM and cisco 3825The status of BRI is ok ISDN BRI0/0/0 interface dsl 0, interface ISDN Switchtype = basic-net3 L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003 Layer 1 Status: ACTIVE ...
Customer has an old amp (McGohen MS-s1004) which connects today to an external transformers RCA connection on one end, and hard wired via analog pair to legacy PBX on the other end for paging purposes.So the question is can I run copper pair from FXS...
I created several Default device profiles and for each subscribed to extension mobility services. I configured my CCM to auto-register phones. Should the Extension mobility service show up? What am I forgetting?
