Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I currently have a 2621 running as our h323 gatekeeper and I wanted to know if there is an IOS software version for a 2801 ISR that supports the "gatekeeper" command. I have looked all through the software pages but have been unable to find it. Ca...
Hello,does Cisco support generally the ISDN Feature "User-to-user signaling" ?I cannot found this information in CCO.Has anybody experience how I can configure on a H.323 Gateway ?Regards David
i have problem that i configuer AA application and put them under dial peer but when the some one call the company and go throw go throw IVR system and the dial by exetion and the person doesnt answer him and the caller close the session the IVR syst...
Hii have 2811 with PVDM2-16 and 4 ports FXO, so each port will take a channel from PVDM2-16, the remaining is PVDM2-12, I want to do HW conference resource using these PVDM2-12, is it possible to do this, since I get that not enough DSP resources whe...
Hi, I currently have two of these MCS-7825-I3 servers. According to this URL:http://www.cisco.com/en/US/products/hw/voiceapp/ps378/products_data_sheet0900aecd805efb09.htmlit is stated that these are servers for 5.1 or 6.0 Cisco Unified Communications...
Hi,We are using Cisco Call Manager ver 4.2(3)sr1 and voice gw (C3745-IPVOICEK9-M), Version 12.4(13d. We experience the voice choppy issue when receiving/calling external party. Does anyone have any idea on this ? Is it due to ios , voice gw or call m...
I am trying to configure cisco Unified Service Monitor. When I try to add a new CM to the CUSM, it asks for CDR DB user and pass, we create a new user on CM for CDR access on SQL server, but we cannot succesfully pass verification, when we try the sa...
There is an intermittent problem that calls from PSTN to IPT site starts with silence for 5 to 10 sec. the call may disconnect or the PSTN caller hang up
Does anybody know if this can be done? I am being told that in order to use T1-CAS trunks and have Caller ID show on the phones is to use an H.323 gateway.Is it possible to configure my 3845 as a MGCP gateway and still provide caller id to my Call C...
We are running CM 4.1.3 in a network with 12 sites ad about 600 phones. We are also a large user of 911 services. There were over 30 911 calls last week.Anyway, we've created our own 911 monitoring and alerting system that works great. It ties in MSS...
Hi All..Wonder if anyone ever tried using Multicast MOH with ATA? I'm using CCM 5.1 and ATA version 3I tested it with 1 port, it works fine, but when it doesn't seems to work with port 2. Any ideas?Rgds
I have a three server cluster, with multiple remote sites. My concern is that if the pub fails, that the gateways will not register to the fallback servers. Is the "CCM-Redundant Host" command sufficient for this?Thanks
I have callmanager 4.2, with my Voice router as an SRST...my voice router is an H323 gateway...i have 1:1 translations for about 20 DIDs setup in my call manager (IE: 1234 --> 4321)...how can i setup SRST so that inbound DID still works when the call...
I have a colleague with a Catalyst 3560 series PoE switch deployed. There was a power outage recently and they are telling me that when the switch loses power it automatically shuts off the poe section of the switch. They are being told that there is...
There are 2 MCS 7845 configured as CCM cluster. Each 7845 come with 2 NICs. How can I team these 2 NICs as a virtual one worked as active/standby mode ?
