Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi Community,Accedntly i put 3 times wrong password for unity connection administrator password.So the account is now locked. Will it come available after 24 hours or i have to do any other task or methods to enable the account.or any other steps to ...
I nderstand that I can configure a trunk to a VoIP carrier and route international destinations through that trunk in Cisco Call Manager. But can you tell me the requirements if I want my sales staff who are outside the office to use office VoIP for ...
I have a problem with ccm 3.2It was running ok when suddenly the power cut off. The system restart ok to the calls between extensions but when I want to call to or from PSTN, the call not progress. The problem is, I think in the signalling between th...
hi guysi want to ask about cisco IP IVR, overview (all supported features)on this product, can it comes as standalone solution or just a component within IPCC, and how it could be deployed with CCM, please if there a link on this thanks alot
Hi,Today i purchased 2 7940's to use in a small office. These need to be SIP based and before i bought i read that there was updates available to the firmware to make them SIP based. I have tried for several hours now to get them from the factory fir...
Hi all,Trying to figure out the best way to handle this. We are running CCM 4.2(3)A staff member who worked at our office had a regular phone line assigned to her cisco IP phone. She then decided she wanted to work from home but wants to be accessi...
Hi,I have an NM-8B-S/T, is this Network module capable of voice?I have inserted this module into a 2811 Router, with IOS 12.4 9T. I don't get any voice-ports? Do I configure something wrong, or is the card simply not capable for voice?Many thanks
Helloi have the following setup:Cisco Callmanager 5.1(1)Cisco 2801 router 12.4(9) with VWIC2-1MFT-T1E1-E1 modulein then CCM i have setup the gateway as an MGCP gateway.The issue is, that every time i reboot the router, and the CCM tries to register w...
I have four seperate analog lines coming into the router to a 4FXO card, in addition I have a VWIC2-1MFT-g703 card and a EVM-HDA-8FXS card installed, the four analog lines have there own numbers assigned, the E1 has a ddi range coming in with some ad...
Is it possible to install CCM 4.1 on the below configurationHP ProLiant DL380 G2Pentium 3 processor, 1.26 GHzWindows 2003 with service pack 11 GB RAMHDD 4 * 18.2 GBNarayan
I'm just curious about what everyone thinks about the Pros & Cons of MGCP and h.323 Gateways with CCM. I know MGCP Gateways are controlled by CCM and h.323 are all router controlled, but what about stuff like: Are calls dropped when the gateways are...
Hi there - I was trying to run some reports on our phone system via the CDR Analysis and Reporting application and it is giving me an error that I have never seen before so I was hoping that someone here may have ran into it before and could let me k...
Hello,We have had a number of calls and entries into QRT Database complaining of Talker Echo on Calls to the PSTN.Some of the time the same PSTN numbers appear more than once both called and calling.Because of this I used a 7940 Phone to send out a T...
Hello,I have a problem when we call and unity answers; if we hang off the phone during the operator speech (during "welcome to the automated attendant, if you ..."), the FXO port of the CALL manager express bundle remains on instead of going off, so ...
is it posible configure the cad to automaticaly login the agent
