Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Situation:We are using Cisco VoIP and are sharing services with our tenants at our business.AT&T is our PRI provider and we PIC to MCI for our long distance (LD).Shared use tenants(Use our phones, but their LD of choice) phones are programmed to 1010...
Can I connect an Avaya PBX to the FXS ports on a VG248, or do I have to use FXO ports for the lines?
Hi,I have unity live record set up, but I have a few questions about it.1. When you are getting near the end of the record time, does you hear a beep or recording telling you it's done recording?2. If there is a beep or recording, do all parties on...
My network ->Analog line on Cisco 1751 as H.323 gateway.C2800 as gatekeeper.CallManager 4.1 with Cisco 7970 telephone.Receive a call on this line. At the 7970 place that call on Hold. Press Resume. You get no audio path and in about 1 minute you g...
The event log says, "The Cisco Telephony Call Dispatcher service terminated unexpectedly."Please give me a clue. thanks
Hi, i have CCM 4.1 with AA co-exist.On the voice gateway (PSTN) i have a voip dial peer pointing to 6000 which is the CTI route point of the AA. evrything is working fine, the problem happens in SRST mode where CCM is down and 6000 is not reachable!!...
The speaker phone specs on a cisco 7940 state that the speakerphone is full duplex. It doesn't appear to behave that way. For example, - user is using 7940 speakerphone for conferencing with other people, - user is talking, other people join Sprint...
I asked this a few days ago but after reading the post, it didn't make since to me either.Is there a way to show line staus of a quick dial extension on Call manager with 7960's and 7914's?
Hi, I need to purchase a module with FXO ports for my 2610 router. The Cisco website doesn't seem to have card compatibility information because this router has reached end-of-life. Can someone tell me which model I should loo for? Just lookin...
Guys,What is the difference between speed dials and fast dials? I am trying to program a company speed dial with one person controlling that list and the numbers assigned to it. What would be recommended in completing this feature? Speed dial or fast...
Hello, I have CME 4.0. I have 5 cards VIC-4 FXO. For DID we have 12 lines (No dial tone from PSTN on this tie lines) and the PSTN is using wink-start signaling.Problem 1: Nothing is being received on my routr for the DID ports. I did some research ...
Hi, tech seniors,I am in a dilema in a IPT design.I am adding a remote site into our existing CallManager cluster.Tt will be a big big remote campus site with around 800 to 1,200 phones. I have two options here:1. Typical SRST remote site.2. Local Ca...
Bug toolkit CSCee20237 saids found in 3.3(4) and resolved in 4.3 but does not give much info. Is this cosmetic, does it cause a problem? What is fix other then to go to CCM 4.3 (win2003) when available or do we just ignore it? It usually happens in t...
HiWe are running CCM 4.2 integrated with an Ericcson MD110.The Gateway is a 2811 running QSIG into a Westell DPNSS Convertor then DPNSS to the MD110.We have had problems with tromboning on the link, ie all channels filling up due to a single call bei...
if i set unity to greeting and transfer to extension 2101 ,how to set unity or callmanager to check that if 2101 is busy it will backward to unity and anouncement to pstn-user that "right now it's not available, please wait for another contact", and ...
