Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, collaboration professionals! Please, answer to my question. Where is 3PCC firmware for 7800 and 8800 series phones. Can I change firmware for existing 7800/8800 phones with CUCM firmware to 3PCC , and if I can, how to do it? Thank you.
Hello, What would be hardware replacement for UCSC-C220-M4S? My understanding is if we need software CCUM and **bleep** support - hardware is needed - right? Thank you
Hi, I have an ATA registered at the CUCME with extension 1502. This extension receives internal and external calls. I need calls coming through that ATA's FXS port to be directed to extension 1504 without calling 1502. I tried to do a call forwarding...
I have a group of three 8851 phones that the hold and transfer softkeys are not appearing. The phones with this issue are all in the same building, and they have the same softkey template as 24 other phones do that do not have the same issue.This iss...
My company uses a lot of VTC systems, such as the DX-80, SX-20 and Desk pro's. We go through a gatekeeper that regularly fails, wanted to know if the RTMT system can monitor the registration status of our systems so I can see which ones are not regis...
Hello, I am trying to learn VOIP functionality on a cisco 2911. I hope someone on here can help me with this. I have a VOIP provider called VOIP.MS I have a Fiber ONT connection going into a Palo Alto Firewall which handles all my routing and DHC...
With 3PCC models can someone explain the differences between the acronyms in the firmware? I know MPP, but what does MER and MES mean and what is the differences?
Hi All,We are trying to interconnect the IMS of an ePC (LTE Network) in SIP client to a Cisco CUCM 12.5. Communications from a Smartphone (LTE Network) to a TOIP (behind the CUCM) work very well. When a TOIP calls a Smartphone, the call is refused by...
Hello,I have ISDN PRI trunks for PSTN calls and use a Cisco CUBE as voice gateway. CUBE to CUCM has SIP trunk in between. In CUCM, we route the calls based on Calling Number. The purpose is to block spam calls in CUCM using translation patterns.Howev...
Hello,So we got some 7811 to replace our old phones that are not supported for the cisco cloud solution. We have the device pack installed and ready to go. We successfully added the device with MAC with the correct device type however when the phone ...
I called support and they recommended I come here for help. My CEO purchased 4 cisco 8851's for our medical practice. However, our phone service is telling me they cannot connect our IP addresses due to activation codes needed for the phones. I have ...
I have an IP Phone 8861 3pcc phone that I am currently trying to provision on a 3CX pbx located on a Windows Server2016 vps instance. The 3CX community was helpful in suggesting I use the fairly straight forward and common provisioning method for gen...
Occasionally a Unity subscriber will receive a message indicating the calling number is the phone number to access Unity. They don't currently have an email alert, this when pressing 5 for message properties. Looking at the logs, the Sender ID is in ...
Hi,We are currently experiencing a problem with our calls, day before everything was working fine and it happend sudenly!CUCM V.14.0.1.12900-161There is a delay of at least 20 seconds before the calls, whether internal or internal to external calls. ...
I am trying to configure a conference DSP resource on the router. Below is the config:voice-card 0 dsp services dspfarmsccp ccm group 999 description Hardware_Resources bind interface FastEthernet0/0.501 associate ccm 2 priority 1 associate ccm 1 pri...
