Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello We have ordered a few 8851 cisco phones and just short of half the Data jack jumpers going to the computer is loose and loses connectivity. any movement of the phone causes connectivity issues to the computer. and telling people to gently s...
Hi team, We have tac opened but without any solution yet. CME ISR4331 IOS "bootflash:isr4300-universalk9.16.03.06.SPA.bin" NTP Configured: in voice register global -> ntp-server 200.160.7.186 mode anycast, + Configured in the router as well ...
Hi We have VoiceGateway with E1 line. Problem we are facing with Voice gateway is, pots and voip dial-peer commands are disappearing after we upgrade. Our operate process is : firstly, we downgrade from the 03.16.05.S.155-3.S5 to 03.15.04.S.155-2.S4,...
Hi All, I need some help here regarding a 7961G IP phone. I tried to convert the phone from SCCP to SIP. However, when I factory reset the phone, the phone kept sending request to the DHCP server. When DHCP server proposed an IP address to it, the ph...
Hi all, This is for CCIE-Collaboration written exam preparation. We need to troubleshoot SIP messages interpretation among UC components like b/w Cisco CUCM to Cisco IM/presence OR Cisco CUCM-Unity etc. Can anybody advise any great book or learning r...
Hello; Is it possible to route the incoming call (at the voice gateway) to certain phone extension based on the caller id? How? For example: If the caller id were 71113391 or 03112233 then the incoming call to this voice gateway to be sent for phon...
Hello all, I am trying to setup meet-me in CME for conference calls. This is my dspfarm config. dspfarm profile 1 conferencecodec g729br8codec g729r8codec g729abr8codec g729ar8codec g711alawcodec g711ulawmaximum conference-participants 16maximum se...
Hi All, We have a CUCM single server in a colo facility with a design similar to this: Site 1 \ Site 2 - tunnels to colo - CUCM - 2921 CUBE - Sip Trunk Site 3 / Last week, in the above example, all was working and then site 3, lost voice capabi...
If I add a partition to an existing inbound CSS that is mapped to my PSTN SIP Trunk in CUCM - does that have any impact on current calls ?
Hello, Want to know if there are any tools with which we can monitor voice quality, and also generate a weekly/monthly report. We do have tools to check network stability, is there any similar tool available to check the quality of VoIP calls.
Hello, Everyone. I almost finished my study of working with CUCM in beginner level. I learned how to configure route (dial-peer) with 3 level architecture RouterGoup -> RouterList -> RouterPattern. I understood that different route group can be used ...
The line voltage for all VG224 ports is low (10-11V).I have change the idle-voltage to high and the impedance to 600r, and it still didn't do any change.Does anybody know how to solve this problem? i need at least 24 volts to operate my analog phones
Dears, I can't access CUCM using IE extension and Firefox too. only can access it through chrome but chrome cann't open icons
I have a 11.5.1 SU4 cluster. I have a RDP configured for a DN with a cell phone listed but SNR is disabled in the entry. From a deskphone registered to my cluster, when I dial the cell phone number, it rings both the cell phone AND the deskphone and ...
CUCM version 11.5 with latest firmware for 7937 Third party call recording solution. Hello,We would like to configure the selective recording for 7937 phones for which we have configured the softkey template with the option "RECORD" when phone is ...
| User | Count |
|---|---|
| 6 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
