Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a remote site using 10 7925G phones and multiple LWAPs and a 2504 controller. Recently the site had a power failure, and now only one of the handsets can connect, the others associate, but fail authentication. Status sits at DHCP_REQD, even th...
Hi All, We would like to ask on why the outside call has no FAC during a conference call. We are polishing the issue with the integrated call accounting in a call manager and as per checking by the support of the call accounting application, there i...
our cube is behind the asa (asa5515) and there is one to one nat. the related ports are open from the provider's sbc. sip inspection is enabled. at random occasions inbound calls have no audio or they drop. after we opened a ticket with the provider...
All, How do I modify the INVITE with CUCM on a SIP Trunk? Specifically I would like to remove h.264 from the Early Offer. SIP Profile/Normalization Script? I have never done this before and am struggling.. So would appreciate any guidance or clear do...
Dear Sir, I have CUCM and cisco mediasense server 11.x. I am using a lot of Cisco 7940 IP phones in our network and try to record the cisco IP phone 7940 phone calls. But I am not able to record the 7940 ip phone in mediasense server because C7940 d...
Hello everyone. We have a customer with a CUCM version 10.5.2. They have one Headquarters and one remote site, on the remote site we have configured with SRST and it has been working very good. Now customer want to implement AAR in order to reroute a...
We currently have 3 SIP circuits coming in but they are all off of ATT. We have redundancy built into the cubes and ATT has redundancy built into the inbound calls. But today ATT had a nation wide outage and of course we were effected and no matter...
Hi. I wonder if anyone can help me. Over a week ago a bought a Cisco IP Phone 303, however it need admin password to reset to factory defaults. The seller is not responding so I stuck with not working device. I went through some tutorial and apparen...
I have a question, is it possible to configure and operate the SRST correctly with other branded sip phones?
Hello Folks, When I saw integrating CUCM and IM&P v9, I could see there was an option to integrate CUCM PUBLISHER where you have to configure everything related to CUCM like IP and AXL. Now I am trying to understand where to put this in 11.5? Please...
SIP TRUNK ITSP Error Code 65 - Bearer Capability Not Implemented with the following call flow.PHONE ----CUCM 9.1.2 ----------SIP TRUNK (DO)---------- ISR 2801 151-4.M12a ----------SIP TRUNK (EO)---------- ITSPMedia Termination Point Required over SIP...
What advantages does CUCM 11.5 have? What we'll achieve if we get rid off 7912 and upgrade to CUCM 11.5?
Hello Friends, I have in my datacenter cisco cucm11 installed "1 pub and 2 subs". recently we needed to make such a change that required we shutdown every server on these servers one after another and perform such a job. I have ...
Hi We have a setup where 3 sites of phones are registered to CME located in our local site. While dialing out from between the sites, calls are ringing but when answered, both parties are unable to hear each other from 7911 phones, whereas when we c...
Hello, I have following setup: Carrier <===SIP Trunk===> CUBE <===SIP Trunk===> CUCM When I try to transfer the external inbound call back to other external number, the Diversion header in SIP message shows internal number (DN of Transferor line o...
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 2 | |
| 2 | |
| 1 |
.jpg "VIP Expert"){kind=icon}
