Activity in Technology and Support
ECMP in FMC is not working properly
I have 2 internet link of 1 Gig, On FTD I am using a 10 Gig link and created sub-interfaces for both the internet links. I have configured ECMP for load-sharing but as I can see the utilization of the links is not happening equally. Sometimes link 1 ...
Stack errors. Are they concerning?
STACK#show switch stack-ports summSw#/Port# Port Status Neighbor/Port Cable Length Link OK Link Active Sync OK #Changes to LinkOK In Loopback------------------------------------------------------------------------------------------------------------...
CISCO ACI Local SPAN Configuration
Hi everyone. We have a requirement to SPAN traffic locally from a compute switch (Nexus 9k) of Cisco ACI fabric. With the traffic spanned I can see with my logic with zeek script that, we are having about 6% of capture loss.For the interface, I run t...
Change Zone Name in FMC
I am using FMC 7.6.4 and I want to change the Zone name from DMZ to WAN. When I try to do it under Object > Object Management > Interface > Edit Zone, I see a message appear as "please confirm, you must apply sensor policy for security zone change". ...
Remote Access VPN DNS Resolution Issue - Cisco FMC
HelloI'm experiencing DNS resolution issues with Remote Access VPN configured on Cisco FMC version 7.4Cisco Secure Client connects successfully to FTD managed by FMC. Authentication passes without issues.Client receives:- Correct IP address from VPN ...
Resolved! unnumbered interface bahaviour
in IOS XE, when you configure an unnumbered interface to borrow address from another interface other than loopback, it will not show up in RIB thus is not able to return the traffic. a static route needs to be configured to point to the unnumbered in...
Firmware and boot code for SG300-52MP
Hello to all,last night power fall out and after that my cisco SG300-52MP doesnt work right. Only green power led blinking and yellow PoE led lighting. I think, firmware is corrupted. I search for firmware and boot code for this model, but no success...
Webex app over MRA fails to download config files from CUCM
CUCM 12.5 / Expressway 15.2.4 / Webex App on AndroidHave MRA configured via Exp-E and -C with Webex mobile app on the client end, SSO is configured on Webex/Exp/CUCM and is working as expected, however, while I can complete the sso login via the app,...
Need expert advise on how to block specific number on Inbound calls
Hi All, I wanted to check if the link below is legit on how to block a specific phone number ( inbound/incoming calls) on Call Manager. If not, please advise or help on how to proceed on getting this done. Thank you in advance and have a great day!...
IW9167E AP Ping Problem From WLC
Hello everyone,I have a problem with my IW9167E access point running the WGB software. The AP is connected to a switchport configured as trunk, and behind the switch I have 2 VLANs:1x VLAN for management1x VLAN for trafficThe AP and the switch both h...
Resolved! CML Memory Utilisation Limit
Hi, we have deployed CML 2.8 on baremetal and are hoping there is a way to adjust the system memory utilisation limit of 80%? Our server has 256GB of RAM and an 80% limit on large servers is quite a waste. We were hoping to be able to run at least a ...
CSCvk05446 FMC should not monitor Standby FTD interfaces
Does anyone else have the problem of a Standby FTD throwing interface alerts for "Interface 'Port-channel<#.VLAN>' is not receiving any packets" in FMC monitor/alerts? ...it's a Standby FTD, in HA mode, so networking is suspended until it becomes act...
Difference between C1-C2960X-48FPD-L and WS-C2960X-48FPD-L part number
Hello,I am looking for an official clarification regarding the difference between the following Cisco part numbers:WS-C2960X-48FPD-LC1-C2960X-48FPD-LI was unable to find an official Cisco datasheet or product page for C1-C2960X-48FPD-L on the Cisco w...
Does FTD support TACACS+?
Does Firepower Threat Defense (the latest version) support TACACS+? edit: Does Firepower Management Center support TACACS+ either?
Add AI (Artificial Intelligence) Category to OpenDNS
This is a feature request to add a new category to OpenDNS Category Blocking. AI is something that absolutely needs to be its own category and blockable without adding individual custom domains. Thank you for your attention to this matter
| User | Helpful Count |
|---|---|
| 146 | |
| 96 | |
| 52 | |
| 37 | |
| 30 |
