Activity in Technology and Support
Meraki MX64 - HA
Hello Dears we have MX64 configured and connected as HA if the down link down for main , is the spare will be active after the down link fail ?
Cisco ASA 5555 not fully showing RAM.
Hello everyone!We have a Cisco ASA5555 with onboard 16 Gb of RAM. Though when we launch the device - it only shows 4 Gb. The ASA version is 9.14(4)24. Tried to re-seat the modules - no luck. Also tried ti switch to diffrent working ones from other 55...
CSCwk14021 - Vulnerabilities in apache-log4j 1.2.15
Can anyone confirm that for this bug the only solution is to upgrade from 3.3 to 3.5?
Can't access internet cross BGP Route
Hi everyone, based on this diagram, how can PC3 access internet cross BGP Protocol?
cisco ACI - Error 400
Dear ACI Experts,We are running a problem with ACI, none of our BDs are able to get submitted and we are getting the below 400 error for all BDs in our prod tenant. we have mapped all our BDs to EPGs in one-to-one basis. subnets are configured in EPG...
Firewall Ftd hardening using fmc
Hi everyone, I have deployed ftd 3105 and ftd 3120 firewalls HA pair. Managing these HA through FMC 1700 physical appliance . I have to deploy minimum security baseline on these if someone knows about any documents which have complete navigation and...
Policy Based Routing with NAT not working as expected
The system consists of a switch with two VLANs for hosts, and a router with two WAN connections.Switch:Interface vlan10 - 192.168.1.1/24, with some hostsInterface vlan20 - 192.168.2.1/24, with some hostsinterface g0/12 - 172.16.0.2/252, uplink to rou...
Resolved! Lockdown Cisco 840
I am deploying some Cisco 840 wireless phones for the first time and we want to lock them down so they are just a basic phone. We don't want them to have the play store or any apps really. The only document I can find seems to show me how to do thi...
Getting Started with Cisco APIs
Trying this for the first time:1- I created My Apps & Keys2- Setup everything in Postman.3- This is basically my code:import requests url = "https://cloudsso2.cisco.com/as/token.oauth2" payload='response_type=code&grant_type=client_credentials&clie...
Office and Outdoor WLAN Modernization - Ruckus to Cisco 9800-CL & Out
Hello everyone,We are planning a significant upgrade and modernization of our WLAN network at our office location which requires inside and outdoor coverage, specifically focusing on providing robust outdoor Wi-Fi coverage based on a recent site surv...
Not getting SSH access of WAN switch from end device
Hello, For WAN switch access, I have connected cable from CORE to WAN switch with trunk configuration on both the ports.I am able to get ping and SSH access from core switch and access switches, but not getting ping and SSH access from end device(L A...
Resolved! Firmware for SG 200-26P
Hello everyone,I'm new in here and just found out that the above mentioned switch is no longer supported by Cisco. This also means that I can't download firmware versions which are newer than mine (1.0.0.19). Anybody here who can help me out with new...
Firepower 2110 with ASA 9.17.1
Hello Guys,I have a cluster of Firepower 2110 with ASA 9.17(1)20, and I have ASDM 7.18(1)20. I want to upgrade the Firepower because of recent vulnerabilities on ASA.What is the recommended version for ASA ? I have checked on Cisco software and there...
Advisories should factor in actual software versions of the devices
Advisories do not compare affected software versions of a security advisory with the ones used in the environment. A recent example is CVE-2024-6387, which just affects IOS XE 17.14, and is fixed in 17.15.1 Devices running IOS XE 17.9.x are flagged a...
Replacing a faulty FTD with a new one on FMC
Due to an error, an IT staff factory resetted a working FTD. The FTD was registered to a FMC with a valid licenze subscription. I have to reassociate my resetted FTD to FMC. Is there a way to do this without making again all configuration? I'd like t...
| User | Helpful Count |
|---|---|
| 120 | |
| 110 | |
| 83 | |
| 62 | |
| 56 |
