Activity in Technology and Support
802.1ad (Q-in-Q) in WS-3560X-48T-L
Hi all,I need some help if there is any possibility to create L2 trunking on a switch WS-3560X-48T-L, according to a manual found this feature is not available for this LAN base switch saying "IEEE 802.1Q and Layer 2 protocol tunneling are not suppor...
Finesse workflow to POST metadata to CalabrioOne
Hello Experts,We want to pass metadata from PCCE-Finesse to CalabrioOne.We used the HTTP POST API call to https://calabriocloud.com/api/rest/recordingcontrols/metadataand pass the JSON body:{ "acdServerId":"13", "acdId":"6174", "metadata" : ...
CML - SandBox Reservation Query
I have noticed the maximum reservation limit is now 50. Earlier it used to be higher.I am just confirming is it me seeing that option only ??Also, just wondering, if is there any plan to increase it in future ?
Questions about WLC 9800 in DR (Redundancy) site - VLAN best practices
Dear all,We are designing a new site for redundancy in the customer's environment, and it has shared the same networks and VLANs as the production environment.The networks will not communicate because we won't have VLAN extensions. However, I think t...
Webex Customer Assist join/unjoin status not propagated within XSI
We’ve run into a weird issue with the Webex Calling API: XSI API, which comes from the old BroadWorks setup. As you probably know, the XSI API has two bits:XSI-Actions: standard request/response styleXSI-Events: real-time streaming eventsThe question...
What’s the real difference between Cisco Catalyst 9200 and 9300 in eve
Hi everyone,I’ve been setting up a few enterprise networks recently and ended up using both the Cisco Catalyst 9200 and 9300 switches. On paper, they look pretty similar — both offer Layer 3 features, PoE+, stacking, and solid reliability.But in real...
ASA VTI Configuration with Single Egress Interface – Is It Possible?
Hi everyone, I'm trying to set up IPsec tunnels between Cisco Secure Access and an ASA device.Based on the example in the following IOS XE guide, I ould like to use a single egress interface on ASA to establish multiple VTI tunnels with the same pee...
MTU configuration required for VXLAN deployment
Hello All-I am reviewing a new campus VXLAN deployment. The one thing always confuses me is the required MTU configuration across all the new switches.Currently I see on all switches following configured "system mtu 9198". However at the same time si...
Resolved! jabber on iPhone
Good day team!Today i saw on iPhone error when connecting to jabber. I didn't see any prompt to accept cert issued by internal enterprise CA/Now jabber just says - 'An invalid certificate was declined. Send problem report.'Android phones working fine...
Resolved! ISE 802.1x PEAP-EAP-TLS Auth with Entra ID ISE 3.5 Availability
We have recently Migrated from EAP-TLS to PEAP-EAP-TLS against Ad and Entra, AD side works awesome, but I know availability to be able to pull device/ user groups from Microsoft Entra is included in ISE 3.5. We have been patiently waiting, but was wo...
Has the FTD the capability of being configured with Loose RPF?
Hi to all,i am wondering if i can configure FTD with loose RPF instead of strict RPF which (i suppose) that is currently running.I am getting a whole lot of syslog messages with id 106016: Deny IP spoof from (194.x.y.z) to "My GW IP" on interface vla...
ASA 9.20 no anyconnect vpn management profile?
Hello,we've 2 prod Firepower 4112 running 9.22 interim and a test Firepower 2110 running 9.20 (no 9.22 for 2110 available)I want to try to establish a anyconnect vpn management Tunnel but on the 2110 when I want to add a Client Profile under "usage" ...
Fast busy on outbound calls
Hello Everyone,Today I am going through an issue, I have never experienced.We have a CUCM and a 3rd party PBX, we have connected both the PBXs over a SIP trunk.I have created an Extension 2045 in the 3rd Party PBX and created a route pattern with th...
Cube for Small branch office
Hi Team,We need to set up a new small branch office for 15 users with SIP PSTN service, integrated with our on-premises Call Manager. For this requirement, I’m considering an ISR router and believe the ISR 1000 series should be sufficient, rather tha...
Resolved! Interfaces going into "suspend mode" when adding vlans allowed
I couple of times I neglect to see that a physical interface is part of a port channel while adding a "vlan allowed" to a trunk interface. This causes the interface to go down into suspend mode after a few seconds, as the "vlan allowed" command needs...
| User | Helpful Count |
|---|---|
| 118 | |
| 87 | |
| 81 | |
| 67 | |
| 62 |
