Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! MSE Appliance Stops Responding
After upgrading our Cisco MSE to 7.4, the appliance does not stay connected to the network. Once the appliance is restarted, layer 3 echoes occur for about 2 minutes and then stop. The only way to get it to respond again, is to restart the applianc...
Hi, From the document, it said only 50 AP supported in each branch for 7500. My case is the HQ has about 100 AP and other BO has less than 10 for each. I am planning to deploy 7500 in the DC and all the AP are in flexconnect mode. ...
Resolved! AIR-LAP1142 Booting to Rommon
I have a customer that has an air-lap1142. He says that it boot to Rommon, and he has to issue the boot command to get it to boot. What is the rommon command to have the ap boot to the image automatically?
please i need help,i have more than 8 month when i install CSM 4.1i haven't any problem with using CSM 4.1but now i want to know how can i archive logs files and before purgingand how can i saving reports and events to an exetrnal disc
Hello I need to upgrade the firmware on the WLC (from 7.0.2 to 8.4?) however, i have more than 50 APs connected on the main WLC, and i don't want to upgrade all of them in 1 shot. I have a backup WLC, so can i upgrade 1 WLC (the backup one) and migra...
is this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do the following take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWA...
The WCS server's C drive, where WCS is installed and the DB is stored, is running out of disk. Most of the disk being used is the WCS db, so there are few options to free up space. I ran a "dbadmin -info defrag" to see how much space would free up ...
Hi,I have a couple of 1040N autonomous APs want to convert to light weight APs.Please help me to acheive this.
Resolved! More explanations about MESH and 802.11n
Hello,I just begin WiFi installations and I have some existential questions.I have 5 Cisco 1552-E APs. One of them is wired to LAN and act as RAP, the 4 others are MAP.On each AP, I use 1, 6, 11 channels as 2,4GHz non-overlapping c...
Hallo, I can't find official information, that could WiSM module whit any other Access Points like TPLink or D-Link work, when I CAPWAP use. In other situation, which AP will be Support. BR Karl
Hi,i have a few AP in flexconnect (H-Reap) mode. i am using a common ssid for centrally switched which works fine on other offices deployed with h-reap AP;s but for 1 office that users connect.if i look at the clients page i see the status is Associa...
Resolved! Cisco 1250 AP
Hi,I seem to be receiving the message 'error VLAN 1 doesn’t exist on 'Radio1-802.11N 5GHz ' (see services>VLAN) whenever i try to enable it on the web portal Security> SSID Manager > tick box Interface Radio1-802.11N5GHz.I have checked and can confi...
Hi,I would like to disable account lockout for ISE Guest accounts resulting from login failures. In the ISE, there is a setting for Maximum Number of Login Attempts (with values from 1-9) in: Administration>Guest Management>Settings>Guest>Port...
Dear All,I configure IP address on the management interface port 1 of 5508 controller when i connect it direct to my laptop i can't ping or access controller from my laptop even i connect through layer 2 switch still i can't not.IP Address of managem...
Hi All,I recently migrated APs from a 4400 to 5508 which had the 7.4 code and encountered an issue that I haven'tsee before, in short the APs would never join the 5508 even when the selction rules said it should.The AP would get a discovery response ...
