Wireless

Resolved! 1242-AG Repeater Mode Fails To Associate to 1242-AG Access Point

HiI have just installed 3 access points along with 6 repeater access points all running V12.4. They are all AIR-AP1242AG-E-K9 using the 2.4GHz radio.Prior to installation I bench tested that the repeaters would associate with the access points and if...

AIR-WLC-2106-K9 locks up - only power cycle will fix

I have the following equipment 1 x AIR-WLC-2106-K9 (IOS = 6.0.199.4)4 x AIR-LAP1131G-E-K9 (IOS = 12.4(21a)JHB1)All configued ok with 2 SSID's associated to 2 VLANS all operates as expectedHowever every few 2 to 12 hours the WLC crashes, locks up.Unab...

Resolved! 1242 and 1310 Bridge?

Hello,Is it possible to make a bridge using a 1242 and a 1310? I have been able to get them to associate together and it appears it will function as a bridge. I have the 12(4) 253 JA IOS for both devices. I would like to use the g antenna on the 1242...

Resolved! WLC 5508 and Cisco Aironet 1242 LWAPP AIR-LAP1242AG-A-K9

i have deployed wlc 5508 ( image 7.0.98.0 ) with 1262N AP and all 45 AP's are working fine,at the same site i had AP1242 which i have converted to LWAPP (8 of them), these accesspoint are registerd perfectly with 5508 but non of the radio's are up. i...

Power adapter required for AP

The power adapter does not work for my AP. So I require a new Power adapter for CISCO Wireless Access Point (Cisco AIR-AP-1242G-A-K9). Does the SMB Support (SMBS) cover the replacement for the adapter? Or Can anybody tell me the correct part code so...

Aironet 1410 Bridge Power Injector coax cable length limits

Does anyone have a reference to how far apart an Aironet 1410 Bridge can be from the Power Injector (Dual Coax feeds). I just can't find the specification details. The device comes with a 20' and 50' F-type and I'm looking at 150' runs for both end...

1310 point-to-point bridge in Lightweight mode

how is the 1130 point-to-point bridge work in lighteight mode ?Is this supported on 5508 and on new 2500 series controllers?How does the WCS manage the point-to-point link?I am aware that there is Lightweight software for the 1300 series bridges but ...

Resolved! Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)

Somebody to help me or know how to configure this scenario?Best Regards

AIR–LAP1524SB–A–K9 Power consumption

For a AIR-LAP1524SB-A-K9 Mesh Access Point I need amp (I) and power (W) consumptions of the power source options (12 VDC, 220VAC, etc.).Thank you.

WCS Deployment

Hi; I am new in wireless,and I have the following items for wcs :Header 1Header 2Header 3 WCS-ENT-PLUS-K9 Family SKU for WCS Enterprise PLUS License Products 1 WCS-ENT-PLUS-10000 Cisco WCS Enterprise PLUS License for 10,000 APs, Win/Linux 1 CON...

Resolved! Upgrade autonomous to lightweight using tftp

Hello,I'm have new autonomous 1242 AP without any configuration. Can I convert it to lightweight using tftp? Which image should I use.The current version is 12.3(7)JA5. Many thanks in advance.Rgds,Fauzan

Resolved! https access for WLC

hi,we use cisco 4400 WLC. We want to move it from http to https/how can we do it?Also, how can assign public IP to wlc so that we can access it tru internet?

WLC: How to convert snmp trap to be a syslog message?

Now I'm trying to write software that get information from Syslog message, but I'm facing with the problem about getting statistic of client de-authenticated in a WLC (Software Version: 7.0.98.0), because I cannot find any log about this information ...

Resolved! WCS v7.0.164.0 + Cisco 1142 LWAP AP's

I have deployed a number of AIR-LAP1142N-E-K9 access points at a site, but I have an issue where all access point have defaulted to Channel 1. I have set the perameters on the Lightweight AP Template correctly to allow dinamic power and channel sele...