Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Looking for assistance on call forwarding in CUCM.Situation - An external or internal call rings directly to User A's phone, if User A's line is busy or goes unanswered we want the call to forward to User B's phone. If User B's line is busy or goes u...
Hello, we have a Cisco ISR 4300 voice router with six FXO lines. For some reason the service privider can not configure a header line for them, so when one of these ports is busy a new call to it is rejected. Is there some way to configure a sort of ...
Can someone please advise if it is necessary to upgrade IP end points (Cisco phones and VG gateways) to the specific device defaults based on the CUCM version or OK to leave them as it is if they are already on a minimum recommended version? Got a cu...
Hi,I have configured COR, Please advise if i have done it correctly, as it is not working, where am i doing mistake. !dial-peer cor customname Mobilename Localname NWDname Intname UANname Tollname Local-BRname Allname internalname Mobile-GSM!!dial...
I am running CUCM 12.5 with three servers in the cluster. At some point in the past, a prior employee set up the systems with one single location in mind and had two servers. After some time, another location was added and a third server was introduc...
Hi Support, my name is Teng from YMM a newly member of cisco community, I would like to ask some question regarding on my ongoing project using cisco IP hone, we have a devices Cisco router 2811 and Cisco 7960g series, we follow the instructions fr...
Recently bought 8861-3PCC (secondhand), already have a SPA525G2 connected to Voipfone (UK), liked the look of the 8861 (all that glitters is not gold!). It has been factory reset but won't allow web page access, (it is enabled on the phone settings) ...
Hi, i want to know cisco phone activation process. how do i activate the smart net for ip phones,please need your support for it. thank you
ATA 190 Version 1.2.2(003) CMCU System version: 12.5.1.12900-115. connected to CM without issue, can dial internal, external, and receive calls. The unit will not provide any dial tone.
Hi, I'm working on setting up a network on Packet Tracer 8.2 and I'm wondering if there's a maximum amount of IP Phones allowed per 2811 router. It seems that I'm only able to add 6 to a single router, any phones after that won't register with the ro...
Hi, would like to know how to order a FLEX renovation in CCW: A-FLEX-PL-VMOn-Premises Unity Connection Add-onA-FLEX-NUPL-ENUOn-Premises Calling EnhancedA-FLEX-NUPL-ANUOn-Premises Calling AccessA-FLEX-CCUCS-NU Cloud Connected UC NU Standard ENTA-FLE...
Please advise, we have CME 8.1 installed and working , we are upgrading to CME 12, will the load files work already in flash work, or do i need to have them upgrade too.if upgrade of firmware is required , please direct to page.
I am using CUCM 12.5.1 and I need to make a report that shows the device location, name, and phone number of the end users. Any help is greatly appreciated.
Afternoon all. I'm scaling up a migration from CUCM 12.5 to MS Teams Voice and want to route internal calls placed on the CUCM to existing DNs out via a CUBE to our ITSP (Gamma in the UK). At present I can manually call forward a line to its subscrib...
I am trying to hand off a PRI to a Mitel phone system and I am having issues with Slips. This is the first time I have done it on the 4321 but I have accomplished this many times on 2800 & 2900's. The issue here is in the controller I am unable to se...
