Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, I’m trying to configure SRST site. The phones are configured; SRST reference is configured and added under the device pool. However, when I go the setting on the phone or from phone web page, I‘m not able to see the SRST as a CCUM, only three ...
Hello,I have a trunk from CUCM to GW.In the GW I created the following dial-peer to accept any call: dial-peer voice 15 voip session protocol sipv2 incoming called-number . But no match! In CUCM the SIP trunk status: Unknown - OPTIONS Ping not enable...
Hi allwe do have a Cisco 2821 router running c2800nm-advipservicesk9-mz.124-24.T4.bin on it. We configured it for MGCP as we did for more than 20 locations. It is connected via E1 PRI. The CUCM servers are on 8.5.1. CUCM shows unregistered but route...
Hello,I have a SIP trunk from Service Provider. In the same time, I want to create a SIP trunk from CUCM to CUBE, so the connection will be:CUCM>> --- SIP--- >> CUBE>> --- SIP --- > > Service Provider.My problem is: I have to bind sip with one of the...
Hi I am running CUEAC 9.1 with CUCM version 9.1. My customer wants to upgrade the attendant console to version 10 advanced, but keep CUCM at version 9. I see this is supported from the attendant console documentation I have read. I believe version 1...
Stupid question, but I can't find a way to change NTP servers from the CLI in CUCM 7. I found the Utils commands, but couldn't find any set commands. Thanks.
Hello,I want to migrate phones from CUCM 8 to 10.5. As you know the phones will not trust the new cluster.I read about the migration steps and I want from you to correct me if I’m wrong and to share with me your experience if there is any risk.The st...
Hello,Need your help. We have more than 1000 Cisco IP Phones and it has been segregated based on teams.For example, Sales team uses 200 phones , Customer service team users 400 phones , Management people uses 15 phones etc.The challenge is we need to...
Hi All, I have a issue where the call flow is as below. When i try to establish the call to third party Audio conference through preconfigured user option from MCU i get only raw DTMF tones in the call instead of RTP events. The Sonexis server will e...
Hello All, I plan on re-designing my SIP trunks, currently i have 50 SIP Trunks on site A (HQ) and 50 at site B (Datacenter) being used for all inbound and outbound calls The plan now is to use the existing gateways a create a pooling of 50 Tru...
Hi Experts, We are going to move two of the five UCS servers to other data center where the IP schema will be different.The two UCS server having virtual machines like CM Subcribers, TFTP server, Attendant console secondary, Unity connection Sub, IM&...
Hi AllI have a CUCM 10.5.2.10000-5 and i'm trying to add a 7811 ip hone, but in the listing devices the 7811 does not appear, i was installed le package cmterm-78xx.10-3-1-12.k3.cop.sgn, but the result was the sameThanks....
Hi all,I need to have in my application a device with 100 lines (+/-), now I'm using a third-party SIP device (advanced) but I only can assign 8 lines to this device.To achieve 100 lines I need to use 13 third-party SIP device (advanced), but I can'...
We have 850 IP Phones , models - 7961, 7941, 7975, 7965, 8800, 8900 and 9900 sereis, please let me know how to deploy background image to all the phones with minimal effort. Please advice.
I'm uploading new Music on Hold files for CUCM v6.1. The problem is that when selecting the new MoH file to play when the IP Phone is put on hold, the file does not play. I have checked the file format and that seems ok. Can anybody please tell me wh...
