Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, I have a strange case, i have a CUCM 10.5 with remote sites, the remote sites are connected to the HQ via DMVPN, in the remote site i have three types of IP phones, 7821, 7841 and 8945, the 7821 and 7841 are perfectly okay (takes like 3 minute...
Good Afternoon, I just want to know if there is a way to extract information of RTP streams when streams end and reoriginate there via MTP or TRP resources, even if its posible to enable RTCP in CUCM to take statistics of those streams at CUCM side, ...
When i dial from an ip phone to an analog phone i get a busy tone . but there is no problem when i call any number on the PSTN my design is :Cisco router ( H323 )with 2 FXO ports one of them is connected to the ip telephony network and the other is ...
Hi, We have that scenario where we are trying to call back from CWMS to mobile number however I receive a 102 timer expiry. The call rings the mobile but when answer it stays for 2-5 seconds and then disconnect and automatically dial again and then d...
Hi Guys,I am trying to Recover corrupted CUCM 7.1 by using external CD-ROM but getting following error " Cannot find kickstart file on CD-ROM".Can any one hlep me how to fix this issue.Thanks
I have lots of end user objects in CUCM that does not have a valid User ID / sAMAccountName to do the synchronization without resulting a huge number of "Inactive" accounts. I'm new to VoIP Administration and new to my work place as well. What is the...
Hi , I am try to configure custom soft-key template but not find TrnsfVM option under "Voice register Template. Though I am able to see for the SCCP not for SIP. SVSR-1(config-register-temp)#softkeys connected ? ConfList List all participants in c...
I have new 8845 video phone connected to BE6000 ver 10.5.1have uploaded required firmware.I can see the file in tftp server , but does not show under firmware tab on CUCMrebooted the server, Phones gets IP info , TFTP info properly but does not loada...
We have recently installed a UC540 system with two BRI connections to the ISDN.Incoming and outgoing calls are fine however when a call is received the phone displays 'Unknown number' and 'From: <blank>' regardless of the caller. Even numbers within ...
HII have a problem .i config my gateway 3845,and one FXO interface card on it .but when pstn phone call in ,i can't receive the ANI.the TECO confirm they already send the ANI.but the gateway display invalid data *Aug 28 09:07:54.710: [0/0/3] htsp_sto...
Is there a bug with this or some other reason why a shared line on a SCCP IP Communicator device ignores what ring setting I have applied for a shared line? If I share the same line on a desk phone, the Ring Once, Flash Only, Disable settings work ...
hello everyone,i am tryin to enable the call transfer feature on my cme, i do not know what i am doing wrong.i enabled the sccp and stcapp.i have one 2901. the config file is attached.Regards.sorry for my english.
Hi, I have a VOIP setup with some Cisco 7940G IP phones registering with a external Voip provider, I don't have a Call Manager, I'm using an OpenSource firewall (PFSense) with SIPROXd to eliminate the Nat problem between my Ip phones and the provide...
Hi,I'm having problem registering my two CP-7841-K9 phone with CUCM v10.5. I have 2 CP-7942G, 2 CP-7945G and 1 CP-8831-K9 and they are register without any problem. It's just the 2 CP-7941-K9 that are causing problem.
in CUCM 9.1, I'm trying to setup a speed-dial/shortcut button for a external conference call that users often use. We currently have a setup for another conference number using " * " button at the moment. So, when user hit " * " button, it will dia...
