Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi there,I´ve a CUCM 10.5 and two gateway H323 working for different location. When the call in for GW1 from PSTN and user put caller on hold the music play ok.But when the call in from PSTN GW2 and user put caller on hold, they just listen tone on h...
HI support Unable to reach mpls vg 192.168.20.20 from vg setup is like pstn---------------------vg-----------------------------swith---mpls from switch i am able to reach the mpls side .bit from vg i am not able to reach for your ref attached co...
Hi,we have a shared line which can take 6 calls simultaneously. Let's assume that we have 4 calls going at once on that shared line.A fifth person (who can make a call on that line but is currently idle) wants to barge into one of the existing 4 call...
ATA186 using SCCP work great!7941 Desk Phones using SCCP work great!ATA187 will only use SIP ver 9.3.2.1 will not work. Symptoms: I have an ATA187 that is registered to CUCM 10.5.2 with line 1 configured. I have a princess phone attached for trouble...
The IPPhone DX-650 is installed on a CUCM environment, just without a known reason the message "Phone is not responding. Do you want to close it ?, with an option to click on" wait "or" report problem "or" OK ". Has anyone encountered this problem? ...
Dear All,Kindly assist with this above heading information. My case is that we installed CMBE6 some couple of months ago. Now we want to add second CMBE6 as subcriber but the following issue came up: "Configuring validation with site-ab-cm (192.168.1...
We have several types of call coming in to the same agent. We would like to be able to have it programmed to either give a specific beep or even a whispered message to notify the rep when they are getting of these call types. An example would be wh...
Hi,I have a problem that has been bothering me for a while, I am using CME which is working fine with my sccp phones, I recently acquired cisco 9971 phones that I have registered with SIP. My problem is that the sip extensions cannot call the pstn. P...
Hi All,Calls from Analog PBX to CUCM Cisco phone cannot transfer back to another analog extension in same PABX (no voice)Exten 1 (PABX A)--->Cisco Phone (CUCM)--> Extension 2 (PABX A)Exten 2 can pick the calls originating from exten1 and transfer via...
Please find the attached screenshot ...during IM&P installation i am encountering error.
Hi, anyone have this problem? I've One ATA190 (1.1.2 (005) Feb 6 2015) registered with CUCM 10.5.2, that when goes to SRST fallback, and then when Primary connection CUCM is up again, don't reconnect to CUCM but remain connected to the SIP SRST serv...
We need to configure the lifesize which model is LFZ-021 to works as Phone IP also. Wnybody knows what would be the configuration in the CallManager? I think that only is necessary to add a new phone with dial number and SIP protocol. But is necessar...
Friends,Two sites: HQ and Branch1Total Phones: HQ (200) and Branch1 (100)1 PUB and 2 SUBPUB only for database management and 2 SUB for call processingPUB and SUB1 at HQ and SUB2 at Branch.HQ and Branch are geographically spread through QoS enabled WA...
Hello,i'm a little bit confused. I installed the latest Device-Pack for CUCM 10.0.1. But only support for 8841,8851,8861 was given after this Device Pack. In other Device Packs i also did not found any hints about support for 8811. Is there anything ...
Hi!We are planning a Jabber Rollout. Therefore we're having some issues with the certificates, because they are self signed. The User should not get an error, when opens Jabber for the first time.Now, the certs for CUPS are signed from the internal P...
