Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, I'm Installing a Monitoring service on my environment and it uses SNMP.Until now I was able to configure the SNMP Agent e Trap for the Devices and it works fine, but it need to be configured with the critical services from each, because now, only...
Hi,I am using CUCM 86. And I am using a 3rd party billing software.Does CUCM record any digit that is dialed after the call established?I am calling to a certain PSTN number, and the users need to press certain digit after the call establish, and I n...
Hi All, Can any one clarify to me how to make CIPC connected to Cisco Router VSEC model ,the WAN connection will be through HWIC ADSL with fixed real IP , i want a brief configuraion and explanation , which ip to make source-address is it must t...
Hi,I am working on a Cisco 2921 router ordered with PVDM3 32 to 128 Channels factory upgrade. The DSP looks good in the inventory. However, I am not able to see / allocate all the resources available. I am unable to allocate more resources then curre...
I tried to download cme-full-4.3.0.0.tar and cme-full-7.0.0.1.tar to my gns3 router 3745 IOS (c3745-adventerprisek9-mz.124-25d.bin and c3745-adventerprisek9-mz.124-15.T14.bin) but when I try to load from telephony-service I could not see 7942-7962. W...
Hi!!Some our codecs have same problem. They recieve outbound calls from numbers "100" and "101". And if look clother this calls cominf from the same white IP address as address of codecs. So it means codecs calls by itself. And this call repeats too ...
Something strange happened, all of a sudden, my route pattern 9.@ that used the GBNP is no longer working. I used DNA and it doesn't look like its matching any calls.This may have happened after I migrated the CUCM to VMWare. The DRS restore said e...
Guyz i need to know if its possible to capture RTP streams using G.722 with wireshark and play it ??? and if not can i like change the IP phone settings to another type of codec , im trying to do all this to find out if my voice traffic is encrypted...
Phone configured in CUCM as the correct defined type,DHCP Server option 150 points to the CISCO TFTP Server.Cisco TFTP Services is activated and running.The issues are as follows:(1) 16 phones - NOT showing any display after powering on via good know...
Does anyone know if there is a way for Unity Connection to just forward a message to Exchange w/o setting up Unified Messaging? Airgas has CME now and that what it is currently doing. I was hoping there was a light and easy way to set this up witho...
Should Mobility/SNR work if the primary phone associated with the User ID is a Cisco IP Communicator phone?
Hi,I have two sites with one CME installation each, and an integrated CUE on the second site (site B).If i´m doing a call from site A (7940 sccp phone) to the CUE via the CME of site B, i can´t get the DTMF tones through.If i configure a dial peer on...
Hi buddies.Someone already Record Calls with UCM 8.6 + IP Trade + Redbox Recorder?I configured SIP Trunk + Route Pattern + Recording Profile + Enable BIB + Disable Privacy + configurations in LINE, but just for IP Trade don't works.Have any special c...
When using the relay message option within Unity Connection, is there a way to append the caller's ANI to the message. Using Unity Connection 7.1.5
Hi,CME version 7.1phone 7945when user use headset to answer call, they still can hear audio coming from handset.it is a quite in the office so my customer want to stop the audio from handset when they use headset,if it is possible to do that? ThanksB...
| User | Count |
|---|---|
| 12 | |
| 8 | |
| 7 | |
| 4 | |
| 1 |
.jpg "VIP Expert"){kind=icon}
