Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I just want to confirm that the firmware load I have on the 7962 SCCP phones is current. I see in the Software Download on your site, the latest version is 9-4-2SR3-1.zip. In my Device Defaults I have SCCP42.9-4-2SR3-1S. I just wanted to make sure ...
I'm looking for a list of Cisco approved call recording vendors.Joe
Hi,I did an installation of Jabber Phone Mode Only, I don't have an IMP server, just CUCMs, and on Jabber clients when I do View Profile searches, the CHAT (IM address) always appears.How can I remove this information which does not make sense in my ...
Our client facing problem with ringtone for IP Phones as below:Customer unable to play the ringtones other than Chirp 1 & 2.Customer able to see the other ring tones, when try to access they get error message 'unable to obtain additional ringtones fr...
Hello, I have my 2 expressways with version 11.x and I need to do a hardware migration (no changes no updates) is there any best practices for this? thanks.
Ladies and Gents, Situation: As of today my CUCM (seemingly) has stopped issuing IP addresses. Here's what I now for sure:- CUCM Version 11.5.1.14900-11- ISE 2.3.0.298 Simple topology. Mesh. Network devices are connected to access switches on th...
Hello Experts,Please find attached.we have 2911 Cisco Router and using CME IP telephony. Cisco 74XX Series , 69XX and 9971series Ip phone's are being used.PSTN SIP trunk Outgoing and incoming calls are working fine, except 9971 Series Phone. when we...
Hello, I apologize if this question has an obvious answer, only one of our clients uses a Cisco device so I'm not very familiar with the ins and outs of its operation beyond reloading the current configuration. They're getting a new phone system and ...
All, I am trying to get a network setup to get some 8861 phones working with CME 12.0. To get CME running, I am using 1 phone plugged directly into router for now; then I will expand after I get working. The phone will not pull any config files and i...
Hello all, We are looking at options of cordless phones. We are aware of the 8821 and would rather not have a 802.11 wireless phone. Has anyone used the IP DECT 210/6825 in their CUCM environment?The other option we have is using an ATA191 and an an...
HaiOutgoing calls not work with ITSP, sip-ua show registredhere is debus ccsip messages Oct 24 09:17:43.370: //336/13490923812F/SIP/Msg/ccsipDisplayMsg:Sent:INVITE sip:65139333@XXXXXX:5060 SIP/2.0Via: SIP/2.0/UDP 62.150.254.82:5060;branch=z9hG4bK1F62...
Hello Guys, I'm trying to make SIP REFER work on CUBE but no luck. What am I missing? When CUBE receives the REFER message, it sends "SIP/2.0 400 Bad Request"The goal is to get the CUBE to send an INVITE to the address in the REFER-TO header. I do ha...
Hi everyone, I recently bought a Cisco 8851 telephone, now I want to set it up. However, that prepared me somehow problems. When I connect the phone to the PoE switch and have configured DHCP, the first thing it says is "Welcome - Enter activation co...
Hi Everyone,we have Cisco CUCM with IP phone in the network , my question is there any way to record the calls between my phones , if there is any way could please specify the solution ?
Good afternoon-We have just installed a Vg-450. When we create a POTS line and add the config, it will not register until we reset the entire gateway. After that the port registers and functions correctly.Are we missing something? Steve McFarland
