Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all,After sucessfully intergration of uc with cucm using sip. After making a test call from phone a to phone b . Phone a send the voice msg to phone b, but phone b has no mwi indicator & no msg notification icon also , but when I press msg but...
On Unity Connection 8.5, on the User Basics screen (the 1st one) of any given user, there is a check box for “Set for Self-enrollment at Next Sign-In”.Is there a way to get the system to tell you who still has the box checked (meaning the user has ne...
hi,i need to configure qsic trunk between ccme and pbx.i want the configuration for qsic on ccme.does any one have the configuration?how the dialpeer should be configured?
Tested this gateway before we deployed it in another town and have run into a problem One problem was inbound dialing which I corrected by battery-reversal on the FXO ports. I still have problem outbound though. I see the port go off-hook for a se...
I have a user that needs to delete all messages. In fact, he wants me to delete his mailbox and recreate it.I do not have access to the GUI, only the router.I understand that if I simply delete the user via CLI, it becomes orphaned. The problem is ...
I have a UC540 connected to a BRI in St. Barths and have been having trouble running a client on it. I am looking for some advise on troubleshooting the root cause of the 503 errors I recieve,.
We have CCM 8.x with 19 locations utilizing CP7960 and CP7940 phones. I am looking for a 3rd party web attendant. Currently using Netvista, expensive and unstable.Any help would be great. Also would a Cisco SPA500S (SIP expansion module) work in conj...
Hi,CUCM 8.x integrated with Active Directory, the phone number format at the AD is 123-456-7890 with the dash "-" added. The CUCM IP Phone format will be the last 5-digits of the above format. From the directory we can select to call by the above for...
Hi Guys,i have a scenario were we are moving office into a single building so during intermediate setupi will have 3 CCME s catering 3 offices who will be sharing 2 PRI lines which will terminate on a new Voice gateway. we have applied for the lines ...
I have an existing ACM telephony environment that we are slowly migrating to CUCM environment. We have ACM assigned 4 digit extensions plus CUCM assigned 5 digit extensions. I would like to setup when a call from a CUCM registered station dials a ACM...
We are running CER ver 7.0.1. Does anyone know if it is possible to test a 911 call to see what ELIN is being sent to the PSAP without actually sending the call?
Hi,I have added a new ATA187 in a CUCM but is in unknown state, it is unable to get an IP address. Now is connected in fa0/18 in my Switch, how can add a static IP through a remote console? is possible ?Thanks!
Has anyone else noticed problems upgrading 7941 & 7961 handsets to the latest 9.2 firmware ? We'reseeing problems where phones report "Unprovisioned" after upgrading. Yet, a firmware reset (12345...) fixes the issue.GTG
Hi, I have a situation that both POTS dial-peers and SIP voip dial-peers have the same destination pattern on C2801 which is acting as an IP-IP gateway and MGCP gateway, whenever SIP calls come in from CUCM, C2801 routes the call to POTS dial-peer, h...
Hii have CUCM cluster 8.0.3 working as centralized call processing and i have remote sites with IP phones (7911, 7942 and 7945) plus ATA 187 (version 9.0.3)the phones are working fine but some ATAs are unregistering and will only register with power ...
