Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello,in CUCM 8.5.1.11900-21 I have at an costumer the effect that he logs in to the personal address. After he ends (no logout) the use he have to login again.In older versions the user was logged in until he pressed the logout softkey at the phone....
I have a Cisco 2951 router acting as a gateway (H323) to call manager business edition. The 2951 routers has 3 PRI trunks that terminate into it and handle inbound and outbound calls. I would like to monitor the Call legs and set a threshold to send ...
Hi all,When making ad hoc conference call with 6 persons, how can I press "confrn" to connect others in one CP7942. 1. CP7942 A dial to B2. Press "confrn" in CP7942 to C3. Press "confrn" in CP79424. A, B and C are in conference5. Press "confrn" in CP...
Hi,We're slowly migrating from 7960 to 9951 phones, how do I get the 9951 devices using + dialing from an E164 format or translate it to extensions?The 7960 devices grab their corporate directory from an XML feed, which we provide just the internal e...
Greetings!So I'm in the middle of setting up a CCM 8.5 and Unity Connection 8.5 enviorment. I've setup my call handler, and assigned extensions to them.Issue -- When I dial the main number for the call handler (Assigned extension 6752) the system pr...
Hi everyone. I have a new RightFax (OpenText) server being integrated with my UCM 7.1 cluster via SIP trunk. Outbound calls route through a MGCP-controlled PRI circuit located in the same building. I've set up both ends for T.38 encapsulation.Functio...
All,Has anyone using the Cisco Cius been successful in administrating CUCM with it? I am running firmware 9-2-2 on the Cius, and we are on a 8.5.1.12024-1 CUCM release. Every time I access the CUCM admin page, I can log in and get to the labels, but ...
Hi we just received 5 new 8945 phones and I want to use the G722 codec on them, the question is where can I get this from or does it come installed with CM already. And if it's already on CM where do I go to check and make it the default.
Hey Guys,I've read the cisco docs on ToD routing and it all seems to be very specific for inbound after hours traffic.I have office phones that need be restricted to internal and 911 calls from18:00 to 06:00 during that time frame users need to be ab...
Does anybody have any recommendation for me to upgrade a single CUCN server running 7..0.2 to 8.6.2a ? Eventually I am going to run on virtualized servers. Is there a best practice for this without any downtime? I am thinking of building new virtu...
I am trying to learn about UCCX, we do not have Active Directory integration. I have a CAD agent configured on my desktop and it looks corrrect. I have an IPCC extension and my phone is associated to end user.I see my username in UCCX and have skills...
I thought in ephone-dn you could associate (1) user with (2) devices.. is that not the case anymore? In the GUI on CME, you cant do this, but in the CLI I thought the command was ephone-dn xx username, but its flagging me that the username is used...
Hi,I am installing vmware on a new ucs c210 server. I am going through the bios settings for the boot options but do not have 4 boot options as depicted in the manual. My only option is one boot option which points to a raid controller.Does anyone ...
Hello,I have understood that when an IP-phone is falling to SRST mode, the forward all destination that was configured will disappear.I want to know if it is possible to configure a forward all destination when the IP-phone is in SRST mode?Do I have ...
I recently swapped out computers at work. I was running XP, and now I'm on 7. I reinstalled Cisco IP Communicator on my new laptop. After that I associated it with my account in Call Manager. So now my desk phone and soft phone both have my corre...
