Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,We're looking at a pretty ancient CME install, currently configured for G711u only. However most ITSPs over her prefer or require G711a. At the moment it's working, just about, because the ITSP offers the call initially with G711a and G729 only,...
could you please help me, i found some call from SIP inbound, call direct to extension 206197 but after 9 second call forwarding to 206136 without setting in CUCM and two number are not using in Hunting group Message DetailsSENDER: 10.20.0.12GUID: E...
Hi AllI have a question. In the CME, the GUI service is supported for SIP Phones administration, or is for SCCP Phones only?TIACristian
Hardware: ISR4331 with IOS Version 16.12.4, RELEASE SOFTWARE (fc5)CME 12.5 I have a simple test environment with SIP only and have successfully setup the Jabber client for Windows.The Jabber phone can call my test 7821 and 8945 phones (SIP) with no p...
Dear All, i have CME router 2811 "Router 1"CME Version 7.0(0)IOS Version 12.4(15)XZ2B-ACD configured under dial-peer 100 "H323 not SIP"my connection to GW is via Dial-peer 8, SIP not H323Topology as follow:"GW"------SIPv2--...
hi all, i just deployed a PCD server 11.5, but when i want to add esxi host, eror come : Failed to mount Cisco Prime Collaboration Deployments export as NFS store to the ESXi Host. Please look at the exception details in PCD logs and check the ES...
How to change User Locale in CUCMCan I set the default setting to Korean without changing User Locale in CUCM's phone settings?Most phones display in Korean without editing User Locale settings.However, some phones require the User Locale to be chan...
Trying to update some 7821 phones from sip78xx.10-1-1SR1-4 without CUCM. Setup:1. DHCP server with option 1502. TFTP server3. Downloaded Firmware 78xx.10-1-1SR2-1.zip file. But getting attached error on TFTP server.
We have an XML phone service for a menu that shows public announcement options/extensions that can be dialed. When you bring up the menu, each line item has "Offline" written below it. Is there a way to hide that or at least a simple way to get it to...
I have many cp-6945 and cp-9971 phones.The pushing of # at boot, and then typing 123456789*0# method works for cp-6945 but not for cp-9971.There's a CP-9971 phone, which works fine but has it's display divided to two, so nothing can be read, or video...
Bit of a newbie question. We’re trying to set-up 2 CP.7841 phones with the Call Manager on a Cisco 4431 router. The phones are not registering on the router. The router version is 16.9. The phone’s original firmware version was SIP78xx.12-0-1-11. We...
7911 factory reset fails.RED LED does not blink even if # is held down for several minutes.Is there a good way??
Hello team, quick question about upgrading the SX10 / SX20 systems. I see in the logs that those systems try to request the following loads:SX10: ce9_13_0-990355df13aSX20: ce9_13_0-990355df13a.pkg The phone gets a 404 (not found) from the TFTP server...
Hello, I'm trying to figure out how to properly configure my 8841s with a shared line. I'm trying to follow the admin guide and I am getting stuck. I am using freepbx for call control. I've got it configured to allow the extension to register multipl...
Hi Guys,we got one Problem with our SIP environment. We have connected an anynode sbc to the cucm to connect to a sip trunk. this works all fine with incoming and outgoing call. today i tried the following szenario.I got an internal call an place thi...
